Ultra-Low-Sulfur Diesel: What the Label Means
Ultra-low-sulfur diesel (ULSD) is diesel fuel with no more than 15 parts per million (ppm) of sulfur, which is 0.0015% by weight. According to the U.S. Energy Information Administration (EIA), most of the diesel sold in the United States for vehicles is now this fuel. It replaced grades that could carry tens or hundreds of times more sulfur.
The label is a rule about one number, sulfur, and the reason for that number is the exhaust-cleaning equipment on modern engines. The sections below explain what 15 ppm means in plain terms, why regulators cut sulfur, how refineries take it out, and where the limit does and does not reach. Compare diesel and biodiesel in the Comparator to see the fuels this limit shapes.
What 15 ppm means in plain terms
Parts per million counts how many parts of sulfur sit in every million parts of fuel. In the tables of the U.S. Environmental Protection Agency (EPA), ppm and weight percent go together: 0.10 weight percent is 1,000 ppm. On that scale 15 ppm is 0.0015 weight percent (15 ÷ 10,000).
Here is what that looks like in a metric ton (1,000 kg, or 2,205 lb) of fuel, the most sulfur it can hold at each level:
- 15 ppm: 15 g (about 0.5 oz).
- 500 ppm: 500 g (about 1.1 lb).
- 3,000 ppm: 3 kg (about 6.6 lb).
- 5,000 ppm: 5 kg (about 11 lb).
EPA says that before regulation diesel could contain as much as 5,000 ppm, and EIA puts the average for high-sulfur diesel in the early 1990s at 3,000 ppm. A cut from 3,000 to 15 ppm is 99.5% (1 − 15 ÷ 3,000), which is EIA's figure. A cut from 500 to 15 ppm is 97% (1 − 15 ÷ 500).
| Label | Sulfur level | Where and when it applied |
|---|---|---|
| Unregulated diesel | Up to 5,000 ppm; about 3,000 ppm on average in the early 1990s | Before EPA began regulating diesel sulfur in 1993 |
| Low-sulfur diesel | 500 ppm maximum | Highway diesel from 1993; nonroad, locomotive and marine diesel in a phase-in from 2007 to 2014 |
| Ultra-low-sulfur diesel | 15 ppm maximum | Highway diesel phased in from 2006 to 2010; all nonroad, locomotive and marine diesel after 2014 |
Why regulators cut the sulfur
EIA says EPA's sulfur rules were meant to enable cuts in harmful emissions of nitrogen oxides and particulate matter from diesel engines. The sharper reason came with the engines. EPA's summary of its 2001 highway rule says the new engine standards rely on high-efficiency catalytic exhaust control devices, and that those devices are damaged by sulfur. The same summary describes the fuel rule as a 97% cut in highway diesel sulfur by mid-2006.
EIA reports that highway engines from model year 2007 on are built to run only on ULSD. Used with advanced exhaust controls, it says, ULSD can cut vehicle particulate emissions by up to 90% and nitrogen oxide (NOx) emissions by roughly 25% to 50%. EIA adds that the cleaner fuel also helps older engines. What particulates and NOx are, and how they are regulated, is the subject of air pollutants from burning fuels.
How refiners take the sulfur out
Refiners remove sulfur by catalytic hydrotreating, a step that reacts the fuel with hydrogen. EIA explains that the same reactions also strip out nitrogen, oxygen and metals. They lower the weight of a gallon and give up a small part of its thermal energy. Where hydrotreating fits among the other steps is shown in how crude oil is refined.
The energy cost is small. EIA estimates that the average heat content of U.S. distillate supply fell from about 138.6 thousand Btu per gallon in 1994 to about 137.5 thousand in 2014, a drop of 1.1 thousand, or about 0.8% (1.1 ÷ 138.6). EIA calls this a minor effect. Those averages cover all distillate, including heating oil, so they measure something different from the single diesel figure in the Comparator: 138,490 Btu/gal (38.6 MJ/L) on a higher heating value basis, from the low-sulfur diesel column of the Alternative Fuels Data Center (AFDC).
Where the 15 ppm limit applies and where it does not
For highway diesel, EPA says the phase-in ran from 2006 to 2010, after which all highway diesel supplied to the market had to be ULSD. For nonroad, locomotive and marine diesel, a mix of 500 ppm and 15 ppm fuel was phased in from 2007 to 2014, and after 2014 all of it must be ULSD.
EPA also lists separate marine fuel caps. In Emission Control Area waters the cap is 0.10 weight percent (1,000 ppm). Outside those areas it is 3.50 weight percent (35,000 ppm), falling to 0.50 weight percent (5,000 ppm) in 2020.
Biodiesel carries its sulfur level in its specification. AFDC lists S15 and S500 grades for pure biodiesel (B100), at 15 ppm and 500 ppm maximum, and S15, S500 and S5000 grades for blends from B6 to B20. The difference between biodiesel and its look-alikes is covered in biodiesel vs renewable diesel.
Common mistakes
- Treating ULSD as a different fuel. It is ordinary diesel made to a stricter sulfur limit, and EIA says it now makes up most of the diesel sold for vehicles.
- Reading "ultra-low" as "zero." The cap is 15 ppm, not none.
- Reading ULSD as a climate label. EIA ties the sulfur cut to pollutants such as NOx and particulate matter. Sulfur is not where the CO2 from burning diesel comes from.
- Reading it as a full quality grade. The label sets a sulfur cap only. AFDC lists other properties, such as cetane number, separately (see cetane number).
- Expecting a large energy penalty. EIA's national estimate shows a drop of about 0.8% between 1994 and 2014.
- Assuming one limit covers all diesel-type fuel. Ship fuel outside Emission Control Areas has a far higher cap, and biodiesel has its own grades.
Frequently asked questions
What does ultra-low-sulfur diesel mean?
It means diesel fuel with a maximum sulfur concentration of 15 ppm, or 0.0015% by weight. EIA says most diesel sold in the United States for vehicles meets this limit. It is the same family of fuel as older diesel, made with more sulfur removed.
When did ULSD become required?
EPA began regulating diesel sulfur in 1993. The 15 ppm limit for highway diesel was phased in from 2006 to 2010. For nonroad, locomotive and marine diesel, ULSD was phased in from 2007 and became the only grade after 2014. The dates are EPA's.
Does removing sulfur lower the energy in diesel?
Slightly. EIA reports that hydrotreating reduces the weight of a gallon and a small part of its thermal energy. Its estimate of the average heat content of U.S. distillate fell from about 138.6 to 137.5 thousand Btu per gallon between 1994 and 2014, about 0.8%.
Is biodiesel the same as ULSD?
No. Biodiesel is made from vegetable oils, animal fats or recycled grease, while ULSD is a petroleum fuel defined by its sulfur cap. AFDC lists a 15 ppm grade (S15) of biodiesel, so a biodiesel product can meet the same sulfur level without being the same fuel.
Sources
- Diesel Fuel Standards and Rulemakings: U.S. Environmental Protection Agency. Accessed November 13, 2026.
- Final Rule for Control of Air Pollution from New Motor Vehicles: Heavy-Duty Engine and Vehicle Standards and Highway Diesel Fuel Sulfur Control Requirements: U.S. Environmental Protection Agency. Accessed November 13, 2026.
- Diesel fuel explained: U.S. Energy Information Administration (EIA). Accessed November 13, 2026.
- Diesel fuel and the environment: U.S. Energy Information Administration (EIA). Accessed November 13, 2026.
- Large reduction in distillate fuel sulfur content has only minor effect on energy content: U.S. Energy Information Administration (EIA). Accessed November 13, 2026.
- Alternative Fuels Data Center: ASTM Biodiesel Specifications: U.S. Department of Energy. Accessed November 13, 2026.
- Alternative Fuels Data Center: Biodiesel Fuel Basics: U.S. Department of Energy. Accessed November 13, 2026.
- Alternative Fuels Data Center: Fuel Properties Comparison: U.S. Department of Energy. Accessed November 13, 2026.
Spotted something wrong or out of date? Tell us through the corrections page. We answer within 10 business days.