Biodiesel vs Renewable Diesel: Two Different Fuels
Biodiesel and renewable diesel both start with fats and oils, but they are different fuels. Biodiesel is made by reacting the fat with an alcohol, which produces a fuel of esters. Renewable diesel is made by reacting the fat with hydrogen, which produces a hydrocarbon that is chemically equivalent to petroleum diesel. Each meets a different fuel standard.
The names make the two sound like variations of one product, and EPA's Renewable Fuel Standard tables list both. The difference matters in practice: it changes how each can be blended, what the finished fuel is made of, and how much hydrogen the plant needs. This article lays out the chemistry first, then the production steps, the blend labels and the emissions measures, keeping combustion and life-cycle numbers apart.
Same raw materials, different molecules
The U.S. Energy Information Administration (EIA) says soybean oil is the main U.S. feedstock for biodiesel, with animal fats from meat processing and used cooking oil from restaurants as other major sources. Renewable diesel can use nearly any biomass feedstock, including those. So the starting point is shared. The finished molecules are not.
Biodiesel, in the Department of Energy's Alternative Fuels Data Center (AFDC) table, is made of methyl esters of fatty acids with 12 to 22 carbon atoms. Renewable diesel is listed with 8 to 25 carbons, the same range as petroleum diesel, and AFDC describes it as processed to be chemically the same as petroleum diesel. AFDC puts it simply: renewable diesel is a hydrocarbon, while biodiesel is a mono-alkyl ester.
| Feature | Biodiesel | Renewable diesel |
|---|---|---|
| Main process | Transesterification | Hydrotreating (hydrogen, heat, pressure, catalyst) |
| What it is made of | Esters of fatty acids | Hydrocarbons |
| Carbon chain length (AFDC table) | 12 to 22 | 8 to 25 |
| Fuel standard | ASTM D6751 | ASTM D975 (the petroleum diesel specification) |
| Blending with petroleum diesel | Sold as blends such as B5 and B20, or as pure B100 | Any proportion, including full replacement |
How each is made
For biodiesel, AFDC describes transesterification, a reaction that turns fats and oils into biodiesel and glycerin. The alcohol is usually methanol, and the catalyst is usually sodium hydroxide or potassium hydroxide. The mass balance is easy to hold in your head: about 100 pounds of oil or fat plus about 10 pounds of alcohol give about 100 pounds of biodiesel and about 10 pounds of glycerin, which finds use in pharmaceuticals and cosmetics. For the alcohol itself, see methanol as a fuel.
One point trips people up. AFDC states that raw or refined plant oil, and recycled grease that has not been processed into biodiesel, are not biodiesel. EIA notes that Rudolf Diesel, who invented the diesel engine in 1897, experimented with vegetable oil as engine fuel, which is a different thing from today's specified fuel.
For renewable diesel, commercial plants mainly use hydrotreating: the fat or oil reacts with hydrogen at high temperature and pressure over a catalyst. EIA says most renewable diesel is hydrogenation-derived (HDRD, also called HEFA) and that hydrogenation takes the place of esterification. Two consequences follow, both noted by EIA. Hydrotreating renewable feedstocks needs significantly more hydrogen than removing sulfur from petroleum diesel does, and where that hydrogen comes from can affect whether the fuel meets national or state biofuel standards. And existing petroleum refineries can be converted to make renewable diesel with modest changes. Other routes, such as gasification and pyrolysis, exist but are less common.
Blends and energy per gallon
AFDC explains the biodiesel labels. B5 is up to 5 percent biodiesel and can be sold as ordinary diesel under ASTM D975. B20 is 6 to 20 percent biodiesel and must meet ASTM D7467. B100 is pure biodiesel under ASTM D6751. High-level blends can affect engine warranties and cold-weather gelling, and AFDC says B100 may raise nitrogen oxide emissions. Renewable diesel meets ASTM D975, so AFDC says it can replace petroleum diesel fully or be blended with it in any proportion.
Biodiesel carries less energy per gallon than diesel. On a lower-heating-value basis, AFDC lists 119,550 Btu per gallon (33.32 MJ/L) for B100 and 128,488 Btu per gallon (35.81 MJ/L) for low-sulfur diesel. That is a ratio of 0.93, so B100 holds about 7 percent less.
A blend falls between the two, and a volume-weighted average shows where. For B20, 20 percent biodiesel and 80 percent diesel:
- 0.20 × 119,550 = 23,910
- 0.80 × 128,488 = 102,790
- Total: about 126,700 Btu per gallon
AFDC lists B20 at 126,700 Btu per gallon, so the arithmetic matches. Against diesel's 128,488 that is about 1.4 percent lower (126,700 ÷ 128,488 is about 0.986), consistent with AFDC's statement of 1 to 2 percent. The Comparator has no renewable diesel entry, so no energy figure for it appears here. Ultra-low-sulfur diesel explained covers the petroleum fuel in the comparison, and cetane number explained covers the ignition rating that applies to both fuels.
What the emissions numbers show
Two measures exist, and they answer different questions. The first is CO2 from burning. EPA's emission factors give 73.84 kg of CO2 per million Btu (69.99 g per MJ) for biodiesel and 73.96 kg (70.1 g per MJ) for No. 2 distillate fuel oil, which is diesel. They are nearly the same. EPA lists biodiesel among biomass fuels and points to separate guidance on how to count them.
The second is life-cycle emissions, which add farming, land-use change, transport, production, distribution and use. For soybean oil biodiesel made by transesterification, EPA's results workbook shows 42.2 kg CO2e per million Btu, against 97.0 for the 2005 average petroleum diesel baseline, which is about 56.5 percent lower. EPA's 95 percent range runs from 14.2 to 75.9, because the land-use change estimate is uncertain.
Do not subtract one measure from the other. The 73.84 and the 42.2 describe different boundaries. Combustion vs life-cycle emissions explains the split.
On the regulatory side, EPA's Renewable Fuel Standard sets a biomass-based diesel category that must meet a 50 percent life-cycle reduction against the 2005 baseline. EPA's lifecycle results page lists pathways for both biodiesel, made by transesterification, and renewable diesel, made by hydrotreating, each with its own qualifying process. See the numbers in the biodiesel and diesel comparison.
Common mistakes
- Treating renewable diesel as another name for biodiesel. The chemistry, process and fuel standard all differ: esters under ASTM D6751 against hydrocarbons under ASTM D975.
- Calling raw vegetable oil biodiesel. AFDC says unprocessed plant oil and recycled grease are not biodiesel.
- Reading B20 as 20 percent less energy. B20 is 20 percent biodiesel by volume, and its energy per gallon is only about 1.4 percent below diesel's.
- Assuming both fuels blend the same way. Renewable diesel meets the petroleum diesel standard and can be blended in any proportion. Biodiesel is sold at set blend levels with their own standards.
- Treating "bio" as zero emissions. EPA's combustion CO2 for biodiesel is nearly the same as diesel's, and its life-cycle figure is lower but well above zero.
Frequently asked questions
What is the main difference between biodiesel and renewable diesel?
Chemistry and process. Biodiesel is a fatty acid ester made by transesterification and meets ASTM D6751. Renewable diesel is a hydrocarbon made mostly by hydrotreating with hydrogen and meets ASTM D975, the petroleum diesel specification. Both are made from fats, oils and greases.
What do B5, B20 and B100 mean?
The number is the percentage of biodiesel by volume in the diesel. B5 is up to 5 percent, B20 is 6 to 20 percent, and B100 is pure biodiesel. Each level has its own specification. Follow engine and fuel-supplier instructions for which blend to use.
Is renewable diesel chemically the same as petroleum diesel?
AFDC says renewable diesel is processed to be chemically the same as petroleum diesel, and EIA calls it chemically equivalent. The difference is the starting material, which is fat or oil rather than crude oil. That is why it meets the same ASTM D975 specification.
What are biodiesel and renewable diesel made from?
Mostly fats, oils and greases. For biodiesel, EIA lists soybean oil as the main U.S. source, plus animal fats and used cooking oil. Renewable diesel can use nearly any biomass feedstock, including those, though the hydrotreating route is the one commercial plants mainly use.
Sources
- Biofuels explained: Biodiesel, renewable diesel, and other biofuels: U.S. Energy Information Administration. Accessed November 13, 2026.
- Biodiesel Production and Distribution: U.S. Department of Energy, Alternative Fuels Data Center. Accessed November 13, 2026.
- Biodiesel Blends: U.S. Department of Energy, Alternative Fuels Data Center. Accessed November 13, 2026.
- Renewable Diesel: U.S. Department of Energy, Alternative Fuels Data Center. Accessed November 13, 2026.
- Fuel Properties Comparison: U.S. Department of Energy, Alternative Fuels Data Center. Accessed November 13, 2026.
- Overview of the Renewable Fuel Standard Program: U.S. Environmental Protection Agency. Accessed November 13, 2026.
- Lifecycle Greenhouse Gas Results: U.S. Environmental Protection Agency. Accessed November 13, 2026.
- GHG Emission Factors Hub: U.S. Environmental Protection Agency. Accessed November 13, 2026.
Spotted something wrong or out of date? Tell us through the corrections page. We answer within 10 business days.