Methodology and sources

Every number in the Comparator is copied from a published table of an official source. This page explains what each measure means, how a value is recorded, how units are converted and where the data has limits.

Last updated

What the Comparator measures

  • Energy per mass. The heat released when one kilogram (or pound) of the fuel burns completely.
  • Energy per volume. The same, per liter or gallon, in the form the source gives. A liquid is measured as a liquid at ambient conditions. A gas is measured in the form named in the table, such as gas at standard conditions. Volumes in different forms are not directly comparable, so each value shows its form.
  • CO2 from burning. The carbon dioxide released at the point of burning, per unit of energy, as published by the EPA and the EIA.
  • Life-cycle emissions. A separate measure that follows the whole chain, from production to use. It comes from different studies with different boundaries and is never added to, or mixed with, the combustion figure.
  • Physical state, origin, typical uses and storage. Short descriptions taken from the same kinds of official pages. Storage notes are general descriptions of the physical form, not advice.

Two ways to count heat: LHV and HHV

Burning a fuel that contains hydrogen makes water. The higher heating value (HHV) counts the heat released when that water vapor condenses. The lower heating value (LHV) does not. The Comparator shows both and starts on LHV. Read the longer explanation in Higher vs lower heating value.

Each value appears on a basis only where an official source publishes it on that basis. When a value exists on one basis and not the other, the Comparator says so and does not convert. The published CO2 factors from the EPA and the EIA are stated per unit of HHV energy, and the Comparator keeps them as published.

Where the numbers come from

Sources are ranked by how close they are to the original data:

  1. The U.S. Energy Information Administration (EIA): heat content, emission coefficients and electricity data.
  2. The U.S. Department of Energy: the Alternative Fuels Data Center fuel properties table, and national laboratory publications such as Argonne's GREET documentation and the Oak Ridge data books.
  3. The U.S. Environmental Protection Agency (EPA): the GHG Emission Factors Hub and the Renewable Fuel Standard life-cycle results.
  4. The Intergovernmental Panel on Climate Change (IPCC): default calorific values and life-cycle emissions of electricity technologies.

Wikipedia, blogs, vendors and news sites are not used as the source of any number. The full list of web pages we read is the source register at the end of this page.

How a value gets into the table

  1. We open the source page, spreadsheet or document and find the number ourselves. No value is typed from memory.
  2. We record the number in the source's own unit, with the table name, the edition or date shown by the source, and the day we checked it.
  3. We keep a short verbatim snippet of the source next to the number, so a reviewer can find it again.
  4. If two official sources disagree, we record one as the value and describe the other in a note.
  5. If no official source states a number, the Comparator shows "No sourced value". We do not estimate, average, interpolate or derive one number from another.

How units are converted

The site converts each source value once, with fixed standard constants, into base units. When you pick another unit, it converts from those base units for display. Results are shown with four significant digits.

Constants used for every conversion in the Comparator.
QuantityValue used
1 Btu (International Table)1,055.05585262 joules
1 kWh3.6 MJ (3,600,000 J)
1 pound0.45359237 kg
1 US gallon3.785411784 liters
1 short ton907.18474 kg
1 cubic foot28.316846592 liters

A value given per cubic foot of gas keeps the standard conditions stated by its source. We do not adjust gas volumes to other pressures or temperatures.

Biogenic CO2

Ethanol, biodiesel and wood come from plants. The EPA reports the CO2 from burning biomass separately, as biogenic CO2. The Comparator shows the published factor and labels it "biogenic". It does not subtract anything and does not call the result carbon neutral. The article on what "carbon neutral" fuel claims mean explains why that label needs care.

Life-cycle figures

Life-cycle numbers answer a different question from combustion numbers. They depend on where the study draws its boundaries, which year it covers and which method it uses. For that reason:

  • each life-cycle value shows its scope, as the source describes it;
  • values stated per kilowatt-hour of electricity, or per kilogram of product, are shown exactly as published and are not converted to energy of the fuel;
  • a fuel appears only when an official source gives a suitable figure. Several fuels have none in the Comparator for that reason, and the table below shows which.

Known limits and older sources

The data is a set of published reference values, not a measurement of any particular batch of fuel. Some rows rest on older official publications because they are the most recent official source we could open that states the value. These are the cases a careful reader should know about:

  • Gasoline, energy per gallon: the AFDC table prints one column for gasoline and E10 with a range. We use the no-ethanol (E0) end of that range, which the EIA's heat-content documentation (HHV) and the DOE guidelines (LHV) support. The full range is kept in the data.
  • Gasoline, diesel and propane, energy per mass: the LHV comes from the DOE guidelines for the Section 45Z clean fuel credit (gasoline and propane; Argonne GREET inputs, revised September 2026) and from the IPCC 2006 Guidelines default for gas/diesel oil (diesel). The HHV comes from a different publication, the Oak Ridge Biomass Energy Data Book (2011). Because the two bases come from different publications, small differences from a perfectly matched pair are possible.
  • Jet fuel: energy per mass is the IPCC 2006 default for jet kerosene (LHV only; we found no official HHV per mass). Energy per gallon is an LHV from the Oak Ridge Transportation Energy Data Book (Edition 41, 2025) and an HHV from the EPA Hub.
  • Ethanol, biodiesel and methanol, energy per mass; hydrogen, energy per volume: from the Oak Ridge Biomass Energy Data Book (2011 edition, Appendix A). We read an archived copy because the original address now redirects. The hydrogen value is for gas at 0 °C and 1 atm, not compressed. Other forms of hydrogen appear in other publications and are not in the Comparator.
  • Natural gas and LNG, energy per volume: taken from one Oak Ridge table (2011 edition) so that LHV and HHV share the same reference conditions. For natural gas that is gas at 32 °F and 1 atm. The EIA reports a slightly different 1,036 Btu per cubic foot (HHV) for U.S. 2025 pipeline gas at 14.73 psia and 60 °F. Energy per pound comes from the AFDC table, whose footnotes cite different original sources for some of its HHV and LHV values.
  • Coal and wood: the HHV comes from the EPA Hub (per short ton). The LHV comes from the IPCC 2006 Guidelines defaults, which state no moisture condition. For wood, the EPA value is on a dry basis, so the two wood values may not describe the same moisture and should not be used to derive each other.
  • Methanol, CO2 from burning: from an archived EIA page last updated January 31, 2011. The current EPA and EIA tables do not list methanol.
  • Ammonia: the LHV per mass is from an Oak Ridge prepublication draft and the HHV from a 2024 DOE NETL report. Energy per liter was left out because no source states the basis. The zero CO2 from burning comes from a 2006 DOE report.
  • LNG, per gallon: the AFDC table gives LNG per pound only, so the per-gallon values come from the Oak Ridge table.
  • Wood, per cord: one EIA page gives 20 million Btu per cord without a heating-value basis or a moisture state, so we left it out.
  • Gasoline CO2 from burning: the EPA factor is used. The EIA publishes slightly different factors for finished gasoline and for gasoline without ethanol. The difference is noted in the data.
  • U.S. grid electricity: the EIA State Electricity Profiles for data year 2024, released in November 2025. The EIA expects its next update in November 2026.
  • Life-cycle emissions: natural gas (compressed and liquefied), propane, wood, ammonia and grid electricity have no life-cycle figure in the Comparator. No suitable official figure was found for them.

How often the data is reviewed

The Comparator data was last reviewed on November 13, 2026. We review it at least once a year and whenever a source publishes a new edition. The review date is shown in the footer of every page and in the table below.

Found a mistake?

Tell us through the contact form or at [email protected]. The corrections page explains how reports are handled and lists changes.

The Comparator data table

This is every number the Comparator uses, exactly as published and in the source's own unit. Conversions to metric units, and to pounds and gallons, are made by the site from these values. Energy content appears on two bases, lower heating value (LHV) and higher heating value (HHV), each only where a source publishes it. Data reviewed November 13, 2026.

Values, units, sources and consultation dates for each fuel.
Fuel Measure Value as published Source and edition Checked
Gasoline
How we define it

Conventional motor gasoline. Energy per volume is the no-ethanol (E0) gasoline value: AFDC lists it in its 'Gasoline/E10' column as a range (E10 low end to E0 high end), and EIA's thermal-conversion documentation confirms 124,340 Btu/gal HHV for gasoline blendstock (no ethanol). Energy per mass is the DOE/GREET 'Gasoline (E0)' value. CO2 is the EPA default 'Motor Gasoline' factor, which EPA does not label E0 or E10.

Energy per mass (LHV) 18,680 Btu/lb
Show details

Note. LHV only; no current official HHV per mass found. Mixed basis with energy_per_volume (HHV). The same table (May 2025 edition) gives the same figure. IPCC 2006 Guidelines Vol. 2 Table 1.2 gives a generic Motor Gasoline NCV (LHV) of 44.3 MJ/kg (95% interval 42.5-44.8) for comparison.

Source wording. “Gasoline (E0) 116,090 Btu/gallon (18,680 Btu/pound [lb]) 1.00”

U.S. Department of Energy, Office of Critical Minerals and Energy Innovation: Guidelines To Determine Life Cycle Greenhouse Gas Emissions of Clean Transportation Fuel Production Pathways Using 45ZCF-GREET, Table 1 Rev. September 2026, Table 1
Energy per mass (HHV) 20,007 Btu/lb
Show details

Note. Row 'Conventional gasoline' (no ethanol). Columns LHV Btu/gal, Btu/lb, MJ/kg then HHV Btu/gal, Btu/lb, MJ/kg. LHV in same row: 18,679 Btu/lb. Other rows: Reformulated or low-sulfur gasoline HHV 19,533 Btu/lb (LHV 18,211); CA reformulated gasoline HHV 19,595 Btu/lb (LHV 18,272). Per-gallon HHV 124,340 matches the upper end of the AFDC Gasoline/E10 HHV range.

Source wording. “Lower Heating Value (LHV) [1] Higher Heating Value (HHV) [1] ... Conventional gasoline 116,090 18,679 43.448 124,340 20,007 46.536 2,819”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book: Edition 4, Appendix A, Table A.1 Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Edition 4, ORNL/TM-2011/446, September 2011 (latest edition), PDF p. 201
Energy per volume (LHV) 116,090 Btu/gal Form: liquid at ambient conditions
Show details

Source wording. “Energy Content (higher heating value): Gasoline/E10 120,388–124,340 Btu/gal (c). Energy Content (lower heating value): Gasoline/E10 112,114–116,090 Btu/gal (c)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (HHV) 124,340 Btu/gal Range: 120,388 to 124,340 Form: liquid at ambient conditions
Show details

Note. AFDC's column is 'Gasoline/E10' and its note [2] says the range reflects E0, E10 and indolene reference fuels; AFDC does not label which end is E0. value = upper end, identified as E0 by EIA (MER Thermal Conversion Factor Source Documentation, Sept 2026, https://www.eia.gov/totalenergy/data/monthly/pdf/mer_a_doc.pdf): 'EIA adopted the thermal conversion factor of 5.222 million Btu per barrel (124,340 Btu per gallon) for gasoline blendstock' (GREET1_2025). lhv = 116,090 Btu/gal, which DOE's 45ZCF-GREET manual (Rev. Sept 2026, Table 1) lists as 'Gasoline (E0)'. The low end (120,388 HHV / 112,114 LHV) is the E10 blend. EIA's Energy Explained Btu page lists 'Motor gasoline' at 1 gallon = 120,214 Btu (not labeled E0 or E10; close to AFDC's E10 end).

Source wording. “Energy Content (higher heating value): Gasoline/E10 120,388–124,340 Btu/gal (c). Energy Content (lower heating value): Gasoline/E10 112,114–116,090 Btu/gal (c)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
CO2 from burning 70.22 kg CO2/mmBtu
Show details

Note. HHV basis, combustion only (EPA Table 1 note). EIA's CO2 coefficients page (released Sept 18, 2024, https://www.eia.gov/environment/emissions/co2_vol_mass.php) lists 70.66 kg CO2/mmBtu for finished motor gasoline (ethanol blended in, treated as non-emitting) and 76.11 kg CO2/mmBtu (9.46 kg/gal) for motor gasoline excluding fuel ethanol. The two agencies differ by about 8% for the no-ethanol case; EPA recorded as primary.

Source wording. “Motor Gasoline | Heat Content (HHV) 0.125 mmBtu per gallon | CO2 Factor 70.22 kg CO2 per mmBtu | 8.78 kg CO2 per gallon”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Life-cycle emissions (separate measure) 98.2 kg CO2e/mmBtu Scope: Lifecycle (well-to-wheels) of 2005 U.S. average petroleum gasoline: crude oil production and transport, refining, distribution and combustion. EPA Renewable…
Show details

Scope. Lifecycle (well-to-wheels) of 2005 U.S. average petroleum gasoline: crude oil production and transport, refining, distribution and combustion. EPA Renewable Fuel Standard petroleum baseline (March 2010 RFS rule analysis).

Note. Per mmBtu of finished fuel (EPA's wording); the table does not say HHV or LHV. Stages: fuel production including crude oil 19.2 + fuel distribution and use 79.0. This is a regulatory baseline for the 2005 U.S. average, not a current measurement. EPA's determination letter of 2024-11-15 (epa.gov/system/files/documents/2024-12/hankinson-renew-energy-determ-ltr-2024-11-15.pdf, Table 2) lists baseline gasoline at 99.0 kg CO2e/mmBtu after updating GWPs from IPCC SAR to AR5 ('Baseline Lifecycle GHG Emissions for Gasoline ... Lifecycle Emissions 99.0'). Cross-check: Argonne GREET 2020 (Zang et al., Environ. Sci. Technol. 2021, Fig. 4) labels gasoline BOB at 92.8 g CO2e/MJ cradle-to-grave. Not directly comparable with rows that use other boundaries or units (per kWh of electricity, cradle-to-gate, etc.).

Source wording. “GHG-Table-Disag, ID 366: Petroleum | Baseline Gasoline | Refining | 2005 U.S. Average | Fuel Production 19.2005 | Fuel Dist. & Use 79.0041 | Net Emissions 98.2046 (kg CO2e per mmBtu)”

U.S. Environmental Protection Agency, Office of Transportation and Air Quality: Summary Lifecycle Analysis Greenhouse Gas Results for the U.S. Renewable Fuels Standard Program May 2023 (v1.1, April 2023 update); current file linked from the EPA page as of 2026-11-13
Diesel
How we define it

No. 2 diesel fuel for on-road use. EIA says on-highway diesel sold in the U.S. is ultra-low sulfur diesel (15 ppm sulfur or less). Energy per volume is AFDC's 'Low Sulfur Diesel' column; CO2 is EPA's 'Distillate Fuel Oil No. 2' factor; energy per mass is the IPCC generic 'Gas/Diesel Oil' default.

Energy per mass (LHV) 43 MJ/kg Range: 41.4 to 43.3
Show details

Note. Net calorific value = LHV. TJ/Gg is exactly MJ/kg. Range is the 95% confidence interval given by IPCC. Generic default for gas/diesel oil, not specific to U.S. ULSD. AFDC does not give diesel energy per mass. Mixed basis with energy_per_volume (HHV).

Source wording. “Fuel type: Gas/Diesel Oil Net calorific value (TJ/Gg) 43.0 Lower 41.4 Upper 43.3”

IPCC National Greenhouse Gas Inventories Programme: 2006 IPCC Guidelines for National Greenhouse Gas Inventories, Volume 2 Energy, Chapter 1, Table 1.2 2006 Guidelines (the 2019 Refinement's Chapter 1 does not restate this table)
Energy per mass (HHV) 19,594 Btu/lb
Show details

Note. Row 'Low-sulfur diesel'. LHV in same row: 18,320 Btu/lb. Per-gallon HHV 138,490 equals the AFDC 'Low Sulfur Diesel' HHV. Other row: 'U.S. conventional diesel' LHV 128,450 Btu/gal and 18,397 Btu/lb; HHV 137,380 Btu/gal and 19,676 Btu/lb.

Source wording. “Lower Heating Value (LHV) [1] Higher Heating Value (HHV) [1] ... Low-sulfur diesel 129,488 18,320 42.612 138,490 19,594 45.575 3,206”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book: Edition 4, Appendix A, Table A.1 Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Edition 4, ORNL/TM-2011/446, September 2011 (latest edition), PDF p. 201
Energy per volume (LHV) 128,488 Btu/gal Form: liquid at ambient conditions
Show details

Source wording. “Energy Content (higher heating value): Low Sulfur Diesel 138,490 Btu/gal (c). Energy Content (lower heating value): Low Sulfur Diesel 128,488 Btu/gal (c)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (HHV) 138,490 Btu/gal Form: liquid at ambient conditions
Show details

Note. EIA's MER Thermal Conversion Factor Source Documentation (Sept 2026, https://www.eia.gov/totalenergy/data/monthly/pdf/mer_a_doc.pdf, GREET1_2025) lists 5.770 million Btu per barrel (137,380 Btu per gallon) for distillate fuel oil 15 ppm sulfur and under, and 5.817 million Btu per barrel (138,490 Btu per gallon) for greater than 15 ppm to 500 ppm sulfur. AFDC's 138,490 matches EIA's 15-500 ppm class; EIA's 15 ppm-and-under (ULSD) value is 137,380 (about 0.8% lower). EPA's default for Distillate Fuel Oil No. 2 is 0.138 mmBtu/gal.

Source wording. “Energy Content (higher heating value): Low Sulfur Diesel 138,490 Btu/gal (c). Energy Content (lower heating value): Low Sulfur Diesel 128,488 Btu/gal (c)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
CO2 from burning 73.96 kg CO2/mmBtu
Show details

Note. HHV basis, combustion only. EIA's CO2 coefficients page (released Sept 18, 2024) lists 74.14 kg CO2/mmBtu (10.19 kg/gal) for distillate fuel oil.

Source wording. “Distillate Fuel Oil No. 2 | Heat Content (HHV) 0.138 mmBtu per gallon | CO2 Factor 73.96 kg CO2 per mmBtu | 10.21 kg CO2 per gallon”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Life-cycle emissions (separate measure) 97 kg CO2e/mmBtu Scope: Lifecycle (well-to-wheels) of 2005 U.S. average petroleum diesel: crude oil production and transport, refining, distribution and combustion. EPA Renewable…
Show details

Scope. Lifecycle (well-to-wheels) of 2005 U.S. average petroleum diesel: crude oil production and transport, refining, distribution and combustion. EPA Renewable Fuel Standard petroleum baseline (March 2010 RFS rule analysis).

Note. Per mmBtu of finished fuel (EPA's wording); heating-value basis not stated in the table. Regulatory baseline for the 2005 U.S. average, not a current measurement. EPA's determination letter of 2024-04-26 (epa.gov/system/files/documents/2024-04/rfs-insitu-distill-diesel-fuel-htg-oil-pathway-determ-ltr-2024-04-26.pdf) states 'the statutory 2005 diesel baseline of 97.7 kgCO2e/mmBtu' (updated GWPs). Cross-check: Argonne GREET 2020 (Zang et al., Environ. Sci. Technol. 2021, Fig. 4) labels petroleum diesel at 91.1 g CO2e/MJ cradle-to-grave. Not directly comparable with rows that use other boundaries or units.

Source wording. “GHG-Table-Disag, ID 367: Petroleum | Baseline Diesel | Refining | 2005 U.S. Average | Fuel Production 17.9982 | Fuel Dist. & Use 79.0079 | Net Emissions 97.0060 (kg CO2e per mmBtu)”

U.S. Environmental Protection Agency, Office of Transportation and Air Quality: Summary Lifecycle Analysis Greenhouse Gas Results for the U.S. Renewable Fuels Standard Program May 2023 (v1.1, April 2023 update); current file linked from the EPA page as of 2026-11-13
Jet fuel
How we define it

Kerosene-type jet fuel. EIA defines it as a kerosene-based product meeting ASTM Specification D 1655 (the aviation turbine fuel specification AFDC associates with conventional 'Jet A'). EPA and EIA label it 'Kerosene-Type Jet Fuel'. AFDC's Fuel Properties Comparison has no jet fuel column, so energy per volume and CO2 come from EPA, and energy per mass from IPCC.

Energy per mass (LHV) 44.1 MJ/kg Range: 42 to 45
Show details

Note. Net calorific value = LHV. TJ/Gg is exactly MJ/kg. Range is the 95% confidence interval given by IPCC. Generic default for jet kerosene. Mixed basis with energy_per_volume (HHV).

Source wording. “Jet Kerosene Net calorific value (TJ/Gg) 44.1 Lower 42.0 Upper 45.0”

IPCC National Greenhouse Gas Inventories Programme: 2006 IPCC Guidelines for National Greenhouse Gas Inventories, Volume 2 Energy, Chapter 1, Table 1.2 2006 Guidelines (the 2019 Refinement's Chapter 1 does not restate this table)
Energy per volume (LHV) 128,100 Btu/gal Form: liquid at ambient conditions
Show details

Note. TEDB labels the pair 'gross' and 'net'; its Table B.1 (hydrogen) prints the same two figures as 'Higher heating value' and 'Lower heating value', so gross = HHV and net = LHV (basis recorded as LHV = net). HHV (gross) for this fuel = 135,000 Btu/gal. Naphtha-type jet fuel: 127,500 Btu/gal (gross) = 118,700 Btu/gal (net). Table note: 'Heat content values are approximate. Data are rounded to the nearest hundred.' EIA Monthly Energy Review Appendix A (Sept 2026) lists Jet Fuel, Kerosene Type at 5.670 million Btu per barrel, stated as gross heat content.

Source wording. “Jet fuel (kerosene) 135,000 Btu/gal (gross) = 128,100 Btu/gal (net)”

Oak Ridge National Laboratory (U.S. DOE): Transportation Energy Data Book, Appendix B, Table B.4 Heat Content for Various Fuels Edition 41 (2025), ORNL/TM-2026/4560, p. B-4 (current edition per tedb.ornl.gov)
Energy per volume (HHV) 0.135 mmBtu/gal Form: liquid at ambient conditions
Show details

Note. Recorded in the source's own unit (mmBtu/gal, on the allowed list). EIA's MER Thermal Conversion Factor Source Documentation (Sept 2026, https://www.eia.gov/totalenergy/data/monthly/pdf/mer_a_doc.pdf) gives 5.670 million Btu per barrel for kerosene-type jet fuel (a Bureau of Mines factor), the same quantity per barrel. No LHV found.

Source wording. “Kerosene-Type Jet Fuel | Heat Content (HHV) 0.135 mmBtu per gallon | CO2 Factor 72.22 kg CO2 per mmBtu | 9.75 kg CO2 per gallon”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
CO2 from burning 72.22 kg CO2/mmBtu
Show details

Note. HHV basis, combustion only. EIA's CO2 coefficients page (released Sept 18, 2024) lists 72.23 kg CO2/mmBtu (9.75 kg/gal) for jet fuel.

Source wording. “Kerosene-Type Jet Fuel | Heat Content (HHV) 0.135 mmBtu per gallon | CO2 Factor 72.22 kg CO2 per mmBtu | 9.75 kg CO2 per gallon”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Life-cycle emissions (separate measure) 89 g CO2e/MJ Scope: Life cycle of conventional petroleum jet fuel (baseline used in DOE sustainable aviation fuel comparisons; value originates from ICAO CORSIA methodology,…
Show details

Scope. Life cycle of conventional petroleum jet fuel (baseline used in DOE sustainable aviation fuel comparisons; value originates from ICAO CORSIA methodology, March 2024)

Note. Per MJ of fuel energy (heating-value basis not stated). DOE reproduces this as the petroleum jet baseline; the number is ICAO's (CORSIA), not a DOE/Argonne GREET calculation, so treat it as a reference baseline. EPA's RFS results workbook has no separate jet baseline: its jet fuel pathways are compared against the diesel baseline (97.0 kg CO2e/mmBtu). Not directly comparable with rows that use other boundaries or units.

Source wording. “Source for the petroleum jet fuel baseline of 89 grams of carbon dioxide equivalent (gCO2e)/megajoule (MJ) of energy: www.icao.int/environmental-protection/CORSIA/ ... Methodology for Actual Life Cycle Emissions - March 2024”

U.S. Department of Energy (DOE/EE-2365): Sustainable Aviation Fuel: Reducing Emissions from Commercial Flight (fact sheet), figure 'Life Cycle Greenhouse Gas Emissions of SAFs in GREET', footnote a DOE/EE-2365, September 2024
Ethanol (E100)
How we define it

Neat (100%) ethanol, CH3CH2OH, as listed by AFDC under 'Ethanol/E100' and by the EPA GHG Emission Factors Hub as 'Ethanol (100%)'.

Energy per mass (LHV) 11,587 Btu/lb
Show details

Source wording. “Liquid Fuels | LHV: Btu/gal, Btu/lb, MJ/kg | HHV: Btu/gal, Btu/lb, MJ/kg | grams/gal. Row: Ethanol 76,330 11,587 26.952 84,530 12,832 29.847 2,988”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects…
Energy per mass (HHV) 12,832 Btu/lb
Show details

Note. Source also gives 29.847 MJ/kg HHV and 26.952 MJ/kg LHV. This is the only per-mass figure found for ethanol from an official source; it is an older table (GREET 1.8d.1, 2010). Its per-gallon values (76,330 LHV and 84,530 HHV Btu/gal) are identical to AFDC's current per-gallon values. I could not open the current GREET model (greet.anl.gov returned HTTP 403).

Source wording. “Liquid Fuels | LHV: Btu/gal, Btu/lb, MJ/kg | HHV: Btu/gal, Btu/lb, MJ/kg | grams/gal. Row: Ethanol 76,330 11,587 26.952 84,530 12,832 29.847 2,988”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects…
Energy per volume (LHV) 76,330 Btu/gal Form: liquid at ambient conditions
Show details

Source wording. “Energy Content (higher heating value): 84,530 Btu/gal for E100 (c) | Energy Content (lower heating value): 76,330 Btu/gal for E100 (c)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (HHV) 84,530 Btu/gal Form: liquid at ambient conditions
Show details

Note. EPA GHG Emission Factors Hub 2025 Table 1 lists ethanol (100%) heat content (HHV) as 0.084 mmBtu per gallon (consistent). ORNL Transportation Energy Data Book Ed. 41 (2025), Table B.4, lists ethanol at 84,600 Btu/gal gross = 75,700 Btu/gal net (slightly different; AFDC kept as primary).

Source wording. “Energy Content (higher heating value): 84,530 Btu/gal for E100 (c) | Energy Content (lower heating value): 76,330 Btu/gal for E100 (c)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
CO2 from burning 68.44 kg CO2/mmBtu Biogenic CO2 (reported separately by the EPA)
Show details

Note. Recorded as published, not netted. Same Hub, Table 2 (mobile combustion): 5.75 kg CO2 per gallon. EPA's GHG Inventory Guidance for stationary combustion says biomass CO2 is reported separately as biogenic CO2. Different treatment elsewhere: EIA's current CO2 coefficients page (release Sept 18, 2024) says 'The fuel ethanol component of finished motor gasoline is treated as nonemissive', and EIA's archived 2011 coefficients page lists E100 as 0.00. Hub factor assumes 100 percent of fuel carbon is oxidized.

Source wording. “Ethanol (100%) | 0.084 | 68.44 | 1.1 | 0.11 | 5.75 | 0.09 | 0.01 (cols: HHV mmBtu/gal; kg CO2/mmBtu; g CH4/mmBtu; g N2O/mmBtu; kg CO2/gal; g CH4/gal; g N2O/gal)”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Life-cycle emissions (separate measure) 77.2 kg CO2e/mmBtu Range: 66.1 to 91.1 Scope: Lifecycle of corn starch ethanol, natural-gas-fired dry mill (2022 average) pathway, EPA Renewable Fuel Standard analysis; includes feedstock agriculture,…
Show details

Scope. Lifecycle of corn starch ethanol, natural-gas-fired dry mill (2022 average) pathway, EPA Renewable Fuel Standard analysis; includes feedstock agriculture, land use change, transport, production, distribution and use; range is EPA's 95% confidence interval from land-use-change uncertainty

Note. Per mmBtu of finished fuel (EPA's wording). EPA reports a 21% reduction versus the 2005 gasoline baseline (98.2) for this pathway. Stage values: agricultural impacts 16.5, land use change 27.8, feedstock transport 3.0, fuel production 27.9, fuel distribution and use 2.1; the small 'distribution and use' stage shows that biogenic tailpipe CO2 is not counted as an emission here, so this lifecycle figure is NOT comparable with the co2_combustion value, which is biogenic CO2 at the stack. Other pathways in the same table: dry mill with biomass 60.6, wet mill with coal 117.0. Second authoritative source: Argonne R&D GREET 2024 (ANL/ESIA-24/21, Jan 2025, Table 1 and Table 2) gives corn ethanol direct LCA 43.8 g CO2e/MJ (LHV) plus induced land use change and indirect effects 4.99 g CO2e/MJ, a much lower value because of different model inputs and methods. Not directly comparable with rows that use other boundaries or units.

Source wording. “GHG-Table-Disag, ID 198: Corn starch | Ethanol | Dry Mill NG (2022 Average) | Net Emissions 77.2325 | Percent Reduction 0.2136 | Net Emissions (Low) 66.0689 | Net Emissions (High) 91.0585 (kg CO2e per mmBtu)”

U.S. Environmental Protection Agency, Office of Transportation and Air Quality: Summary Lifecycle Analysis Greenhouse Gas Results for the U.S. Renewable Fuels Standard Program May 2023 (v1.1, April 2023 update); current file linked from the EPA page as of 2026-11-13
Biodiesel (B100)
How we define it

Neat (100%) biodiesel, fatty acid methyl esters, as listed by AFDC ('Biodiesel', B100) and by the EPA Hub as 'Biodiesel (100%)'.

Energy per mass (LHV) 16,134 Btu/lb
Show details

Source wording. “Liquid Fuels | LHV: Btu/gal, Btu/lb, MJ/kg | HHV: Btu/gal, Btu/lb, MJ/kg | grams/gal. Row: Methyl ester (biodiesel, BD) 119,550 16,134 37.528 127,960 17,269 40.168 3,361”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects…
Energy per mass (HHV) 17,269 Btu/lb
Show details

Note. Source also gives 40.168 MJ/kg HHV and 37.528 MJ/kg LHV. NREL Biodiesel Handling and Use Guide, Sixth Edition (2023), Table 2, lists 'Typical biodiesel (B100)' at 16,270 Btu/lb (37.8 MJ/kg) and 119,550 Btu/gal (33.3 MJ/L) without naming the basis (the Btu/gal value is AFDC's LHV figure), so it is close to the ORNL LHV 16,134. Older table (GREET 1.8d.1, 2010); its per-gallon values equal AFDC's current ones.

Source wording. “Liquid Fuels | LHV: Btu/gal, Btu/lb, MJ/kg | HHV: Btu/gal, Btu/lb, MJ/kg | grams/gal. Row: Methyl ester (biodiesel, BD) 119,550 16,134 37.528 127,960 17,269 40.168 3,361”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects…
Energy per volume (LHV) 119,550 Btu/gal Form: liquid at ambient conditions
Show details

Source wording. “Energy Content (higher heating value): 127,960 Btu/gal for B100 (c) | Energy Content (lower heating value): B100 119,550 Btu/gal”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (HHV) 127,960 Btu/gal Form: liquid at ambient conditions
Show details

Note. EPA GHG Emission Factors Hub 2025 Table 1 lists biodiesel (100%) heat content (HHV) as 0.128 mmBtu per gallon (consistent). ORNL Transportation Energy Data Book Ed. 41 (2025), Table B.4, lists biodiesel at 126,200 Btu/gal gross = 117,100 Btu/gal net (different; AFDC kept as primary).

Source wording. “Energy Content (higher heating value): 127,960 Btu/gal for B100 (c) | Energy Content (lower heating value): B100 119,550 Btu/gal”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
CO2 from burning 73.84 kg CO2/mmBtu Biogenic CO2 (reported separately by the EPA)
Show details

Note. Recorded as published, not netted. Same Hub, Table 2 (mobile combustion): 9.45 kg CO2 per gallon. EPA's GHG Inventory Guidance for stationary combustion says biomass CO2 is reported separately as biogenic CO2. EIA's archived 2011 coefficients page lists B100 as 0.00 (different treatment). Hub factor assumes 100 percent of fuel carbon is oxidized.

Source wording. “Biodiesel (100%) | 0.128 | 73.84 | 1.1 | 0.11 | 9.45 | 0.14 | 0.01 (cols: HHV mmBtu/gal; kg CO2/mmBtu; g CH4/mmBtu; g N2O/mmBtu; kg CO2/gal; g CH4/gal; g N2O/gal)”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Life-cycle emissions (separate measure) 42.2 kg CO2e/mmBtu Range: 14.2 to 75.9 Scope: Lifecycle of soybean oil biodiesel (transesterification), EPA Renewable Fuel Standard analysis; includes feedstock agriculture, land use change, transport,…
Show details

Scope. Lifecycle of soybean oil biodiesel (transesterification), EPA Renewable Fuel Standard analysis; includes feedstock agriculture, land use change, transport, production, distribution and use; range is EPA's 95% confidence interval from land-use-change uncertainty

Note. Per mmBtu of finished fuel (EPA's wording). EPA reports a 57% reduction versus the 2005 diesel baseline (97.0). Stage values: agricultural impacts -8.8, land use change 33.6, feedstock transport 2.7, fuel production 13.2, fuel distribution and use 1.5; biogenic tailpipe CO2 is not counted, so this is NOT comparable with the co2_combustion value. Other feedstocks in the same table: yellow grease 13.8, canola oil 48.1, palm oil 80.7. Second authoritative source: Argonne R&D GREET 2024 (ANL/ESIA-24/21, Jan 2025, Table 1 and Table 2) gives soybean biodiesel direct LCA 20.2 g CO2e/MJ (LHV) plus induced land use change and indirect effects 10.16 g CO2e/MJ. Not directly comparable with rows that use other boundaries or units.

Source wording. “GHG-Table-Disag, ID 332: Soybean oil | Biodiesel | Transesterification | Net Emissions 42.1604 | Percent Reduction 0.5654 | Net Emissions (Low) 14.2471 | Net Emissions (High) 75.8900 (kg CO2e per mmBtu)”

U.S. Environmental Protection Agency, Office of Transportation and Air Quality: Summary Lifecycle Analysis Greenhouse Gas Results for the U.S. Renewable Fuels Standard Program May 2023 (v1.1, April 2023 update); current file linked from the EPA page as of 2026-11-13
Natural gas (CNG)
How we define it

Compressed or pipeline natural gas. Energy per pound is the AFDC value for CNG. Energy per volume is a natural gas value for uncompressed gas at 32 °F and 1 atm from the Oak Ridge table, which has no separate CNG row. CO2 is the EPA natural gas factor, which has no separate CNG row either.

Energy per mass (LHV) 20,160 Btu/lb
Show details

Source wording. “Energy Content (higher heating value): Compressed Natural Gas (CNG) 22,453 Btu/lb [1](c). Energy Content (lower heating value): CNG 20,160 Btu/lb [3](b)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per mass (HHV) 22,453 Btu/lb
Show details

Note. DOE's 45ZCF-GREET manual (Rev. Sept 2026, Table 1) lists CNG at 20,267 Btu/lb LHV, about 0.5% above AFDC's 20,160.

Source wording. “Energy Content (higher heating value): Compressed Natural Gas (CNG) 22,453 Btu/lb [1](c). Energy Content (lower heating value): CNG 20,160 Btu/lb [3](b)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (LHV) 983 Btu/ft3 Form: gas (natural gas, uncompressed gas volume) at 32 F and 1 atm, as stated by the source table header 'Gaseous Fuels @ 32 F and 1 atm'
Show details

Note. Source row is 'Natural gas' (GREET), not 'CNG'; the per-ft3 figure is per volume of gas at the stated conditions, not per compressed-tank volume. HHV in the same row: 1089 Btu/ft3. Per-mass in the same row: LHV 20,267 Btu/lb, which equals the CNG LHV in 45ZCF-GREET (DOE, Rev. Sept 2026, Table 1: 'Compressed natural gas ... 20,267 Btu/lb'); AFDC Fuel Properties lists CNG LHV 20,160 Btu/lb. A different official figure for pipeline natural gas (NETL, LHV 927 Btu/scf) is in the next element.

Source wording. “Lower Heating Value (LHV) [1] Higher Heating Value (HHV) [1] ... Gaseous Fuels @ 32 F and 1 atm Btu/ft3 ... Natural gas 983 20,267 47.141 1089 22,453 52.225 22.0”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book: Edition 4, Appendix A, Table A.1 Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Edition 4, ORNL/TM-2011/446, September 2011 (latest edition), PDF p. 201
Energy per volume (HHV) 1,089 Btu/ft3 Form: gas (natural gas, uncompressed gas volume) at 32 F and 1 atm, as stated by the source table header 'Gaseous Fuels @ 32 F and 1 atm'
Show details

Note. HHV companion of the LHV element above (same row, second Btu/ft3 column). HHV per mass in the same row: 22,453 Btu/lb. Note EIA's page lists 'Natural gas 1 cubic foot = 1,036 Btu' with no stated reference conditions or basis on that page. EIA reports 1,036 Btu per cubic foot (HHV) for pipeline natural gas, U.S. 2025 average, at 14.73 psia and 60 °F. This table uses 32 °F and 1 atm for both bases so that LHV and HHV share one reference condition.

Source wording. “Lower Heating Value (LHV) [1] Higher Heating Value (HHV) [1] ... Gaseous Fuels @ 32 F and 1 atm Btu/ft3 ... Natural gas 983 20,267 47.141 1089 22,453 52.225 22.0”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book: Edition 4, Appendix A, Table A.1 Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Edition 4, ORNL/TM-2011/446, September 2011 (latest edition), PDF p. 201
CO2 from burning 53.06 kg CO2/mmBtu
Show details

Note. HHV basis, combustion only. EIA's CO2 coefficients page (released Sept 18, 2024) lists 52.91 kg CO2/mmBtu for natural gas.

Source wording. “Natural Gas | Heat Content (HHV) 0.001026 mmBtu per scf | CO2 Factor 53.06 kg CO2 per mmBtu | 0.05444 kg CO2 per scf (Table 2 also lists Compressed Natural Gas (CNG) 0.05444 kg CO2 per scf)”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Liquefied natural gas
How we define it

Liquefied natural gas, a cryogenic liquid. Energy per pound is the AFDC value. Energy per gallon is the Oak Ridge table value for liquid LNG. CO2 is the EPA natural gas factor, which has no separate per-energy LNG row.

Energy per mass (LHV) 21,240 Btu/lb
Show details

Source wording. “Energy Content (higher heating value): Liquefied Natural Gas (LNG) 23,726 Btu/lb (c). Energy Content (lower heating value): LNG 21,240 Btu/lb (a)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per mass (HHV) 23,726 Btu/lb
Show details

Note. DOE's 45ZCF-GREET manual (Rev. Sept 2026, Table 1) lists LNG at 20,908 Btu/lb LHV, about 1.6% below AFDC's 21,240.

Source wording. “Energy Content (higher heating value): Liquefied Natural Gas (LNG) 23,726 Btu/lb (c). Energy Content (lower heating value): LNG 21,240 Btu/lb (a)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (LHV) 74,720 Btu/gal Form: liquid (liquefied natural gas); source lists it under 'Liquid Fuels', per gallon; temperature/pressure not stated by the source
Show details

Note. Columns: LHV Btu/gal, LHV Btu/lb, LHV MJ/kg, HHV Btu/gal, HHV Btu/lb, HHV MJ/kg, density grams/gal (1,621). HHV = 84,820 Btu/gal (separate element). LHV per mass in this row (20,908 Btu/lb) equals LNG LHV in 45ZCF-GREET (DOE, Rev. Sept 2026, Table 1: 'Liquefied natural gas ... 20,908 Btu/lb'). Conflict: AFDC Fuel Properties (GREET 2019 basis) lists LNG at 21,240 Btu/lb LHV and 23,726 Btu/lb HHV (about 1.6% higher) and no Btu/gal figure. ORNL TEDB Ed. 41 Table B.4 gives LNG only per pound (23,700 gross / 20,900 net Btu/lb).

Source wording. “Lower Heating Value (LHV) [1] Higher Heating Value (HHV) [1] ... Liquefied natural gas (LNG) 74,720 20,908 48.632 84,820 23,734 55.206 1,621”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book: Edition 4, Appendix A, Table A.1 Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Edition 4, ORNL/TM-2011/446, September 2011 (latest edition), PDF p. 201
Energy per volume (HHV) 84,820 Btu/gal Form: liquid (liquefied natural gas); source lists it under 'Liquid Fuels', per gallon; temperature/pressure not stated by the source
Show details

Note. HHV companion of the LNG LHV element (fourth numeric column). HHV per mass in same row: 23,734 Btu/lb.

Source wording. “Lower Heating Value (LHV) [1] Higher Heating Value (HHV) [1] ... Liquefied natural gas (LNG) 74,720 20,908 48.632 84,820 23,734 55.206 1,621”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book: Edition 4, Appendix A, Table A.1 Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Edition 4, ORNL/TM-2011/446, September 2011 (latest edition), PDF p. 201
CO2 from burning 53.06 kg CO2/mmBtu
Show details

Note. EPA has no separate per-mmBtu row for LNG; its Table 2 LNG factor (4.5 kg CO2 per gallon) is built from the Table 1 natural gas factor, so 53.06 applies to LNG. HHV basis, combustion only. EIA's CO2 coefficients page (released Sept 18, 2024) lists 52.91 kg CO2/mmBtu for natural gas.

Source wording. “Table 1: Natural Gas 53.06 kg CO2 per mmBtu (HHV). Table 2 note: LNG: The factor was developed based on the CO2 factor (kg CO2 per mmBtu) for Natural Gas from Table 1”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Propane
How we define it

Propane, also called liquefied petroleum gas (LPG) or propane autogas, as listed in AFDC's 'Propane (LPG)' column (mostly C3H8 with some C4H10). AFDC says vehicle propane (HD-5) must consist of at least 90% propane. A gas at ambient conditions that is stored and sold as a pressurized liquid. CO2 uses EPA's 'Propane' factor (EPA also lists a separate 'LPG' mixture factor, see note).

Energy per mass (LHV) 19,873 Btu/lb
Show details

Note. LHV only; no current official HHV per mass found. Mixed basis with energy_per_volume (HHV). The same table (May 2025 edition) gives the same figure. IPCC 2006 Guidelines Vol. 2 Table 1.2 gives a generic 'Liquefied Petroleum Gases' NCV (LHV) of 47.3 MJ/kg (95% interval 44.8-52.2).

Source wording. “Propane (liquefied petroleum gas) 19,873 Btu/lb 1 lb = 0.17 GGE”

U.S. Department of Energy, Office of Critical Minerals and Energy Innovation: Guidelines To Determine Life Cycle Greenhouse Gas Emissions of Clean Transportation Fuel Production Pathways Using 45ZCF-GREET, Table 1 Rev. September 2026, Table 1
Energy per mass (HHV) 21,597 Btu/lb
Show details

Note. Row 'Propane'. LHV in same row: 19,904 Btu/lb (45ZCF-GREET Sept 2026 Table 1 lists propane LHV 19,873 Btu/lb, slightly different). Per-gallon HHV 91,420 and LHV 84,250 equal the AFDC propane values. A separate row 'Liquefied petroleum gas (LPG)' gives HHV 21,561 Btu/lb.

Source wording. “Lower Heating Value (LHV) [1] Higher Heating Value (HHV) [1] ... Propane 84,250 19,904 46.296 91,420 21,597 50.235 1,920”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book: Edition 4, Appendix A, Table A.1 Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Edition 4, ORNL/TM-2011/446, September 2011 (latest edition), PDF p. 201
Energy per volume (LHV) 84,250 Btu/gal Form: pressurized liquid
Show details

Source wording. “Energy Content (higher heating value): Propane (LPG) 91,420 Btu/gal (c). Energy Content (lower heating value): Propane (LPG) 84,250 Btu/gal (c)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (HHV) 91,420 Btu/gal Form: pressurized liquid
Show details

Note. EIA's Energy Explained Btu page lists 1 gallon of propane = 91,452 Btu, and EIA's MER documentation (Sept 2026) gives 3.841 million Btu per barrel for propane (from NIST enthalpy of combustion and API density); EPA Hub Table 1 lists Propane at 0.091 mmBtu/gal. EIA's 91,452 is within 0.1% of AFDC's HHV; EPA's rounded 0.091 mmBtu/gal is about 0.5% lower.

Source wording. “Energy Content (higher heating value): Propane (LPG) 91,420 Btu/gal (c). Energy Content (lower heating value): Propane (LPG) 84,250 Btu/gal (c)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
CO2 from burning 62.87 kg CO2/mmBtu
Show details

Note. HHV basis, combustion only. EPA also lists a separate 'Liquefied Petroleum Gases (LPG)' row: 0.092 mmBtu/gal, 61.71 kg CO2/mmBtu, 5.68 kg CO2/gal (Table 2 mobile combustion uses the LPG row). EIA's CO2 coefficients page (released Sept 18, 2024) lists 62.88 kg CO2/mmBtu for propane.

Source wording. “Propane | Heat Content (HHV) 0.091 mmBtu per gallon | CO2 Factor 62.87 kg CO2 per mmBtu | 5.72 kg CO2 per gallon”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Hydrogen
How we define it

Hydrogen (H2), as listed by AFDC in the Fuel Properties Comparison (compressed gas or liquid). Hydrogen is an energy carrier, not a primary energy source.

Energy per mass (LHV) 51,585 Btu/lb
Show details

Source wording. “Energy Content (higher heating value) ... 61,013 Btu/lb (c) | Energy Content (lower heating value) ... 51,585 Btu/lb (c) 33.3 kWh/kg”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per mass (HHV) 61,013 Btu/lb
Show details

Note. AFDC also lists LHV as 33.3 kWh/kg. Other official editions differ slightly: ORNL Biomass Energy Data Book 2011 (GREET 1.8d.1) lists 61,127 Btu/lb HHV and 51,682 Btu/lb LHV (142.18 and 120.21 MJ/kg); ORNL Transportation Energy Data Book Ed. 41 (2025), Table B.1, gives 1 kg hydrogen = 134,200 Btu / 39.3 kWh / 141,600 kJ HHV and 113,400 Btu / 33.2 kWh / 119,600 kJ LHV. AFDC kept as primary.

Source wording. “Energy Content (higher heating value) ... 61,013 Btu/lb (c) | Energy Content (lower heating value) ... 51,585 Btu/lb (c) 33.3 kWh/kg”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (LHV) 290 Btu/ft3 Form: gas at 32 °F (0 °C) and 1 atm (not compressed)
Show details

Source wording. “Gaseous Fuels @ 32 F and 1 atm | LHV: Btu/ft3, Btu/lb, MJ/kg | HHV: Btu/ft3, Btu/lb, MJ/kg | grams/ft3. Row: Hydrogen 290 51,682 120.21 343 61,127 142.18 2.55”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects…
Energy per volume (HHV) 343 Btu/ft3 Form: gas at 32 °F (0 °C) and 1 atm (not compressed)
Show details

Note. Other published forms (DOE, not recorded as primary): (1) DOE Fuel Cell Technologies Office training module 'Hydrogen Properties' (Module 1, Rev 0, Dec 2001, https://www.energy.gov/documents/fcm01r0pdf), Table 1-4, energy density on an LHV basis: 270 Btu/ft3 (10,050 kJ/m3) gas at 1 atm and 60 °F; 48,900 Btu/ft3 (1,825,000 kJ/m3) gas at 3,000 psig and 60 °F; 121,000 Btu/ft3 (4,500,000 kJ/m3) gas at 10,000 psig and 60 °F; 227,850 Btu/ft3 (8,491,000 kJ/m3) liquid. (2) DOE Hydrogen Program Plan 2024, footnote 59: 'the energy density of liquid hydrogen (71 g/L) is equivalent to 2.4 kWh/L'. (3) ORNL TEDB Ed. 41 (2025), Table B.2: 1 kg hydrogen gas = 423.3 standard cubic feet (no Btu/scf figure stated). EIA says hydrogen has 'the lowest energy content by volume as a liquid (about four times less than gasoline)'. This figure is from an older table (GREET 1.8d.1, 2010); its per-pound values differ from AFDC's current ones by about 0.2 percent.

Source wording. “Gaseous Fuels @ 32 F and 1 atm | LHV: Btu/ft3, Btu/lb, MJ/kg | HHV: Btu/ft3, Btu/lb, MJ/kg | grams/ft3. Row: Hydrogen 290 51,682 120.21 343 61,127 142.18 2.55”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects…
CO2 from burning 0 kg CO2/mmBtu
Show details

Note. Zero stack CO2 from the fuel itself. The same EPA document says high hydrogen blends by volume 'also have the potential to increase nitrogen oxide (NOX) emissions from the combustion turbine' (combustion in air can form nitrogen oxides). Not a life-cycle figure: it says nothing about CO2 from producing the hydrogen.

Source wording. “Hydrogen does not contain carbon and therefore emits no carbon dioxide (CO2) when combusted. ... The direct benefit of combusting hydrogen to produce electricity is zero CO2 emissions at the stack.”

U.S. EPA, Office of Air and Radiation: Hydrogen in Combustion Turbine Electric Generating Units, Technical Support Document May 23, 2023
Life-cycle emissions (separate measure) 12 kg CO2e/kg H2 Scope: Cradle-to-gate (natural gas extraction through hydrogen at the plant gate; excludes delivery and end use), steam methane reforming without carbon capture and…
Show details

Scope. Cradle-to-gate (natural gas extraction through hydrogen at the plant gate; excludes delivery and end use), steam methane reforming without carbon capture and without steam credit (NETL Case 1A), U.S., IPCC AR5 100-year GWP

Note. Per kg of hydrogen (functional unit: hydrogen at the plant gate), not per MJ; the unit needs conversion with hydrogen's energy content. Case 1B (SMR integrated with an industrial user of the excess steam, with a steam displacement credit) is 10 kg CO2e/kg H2; the source gives two plant configurations, not a statistical range. Represents today's predominant production route (natural gas reforming without capture); NETL's cases with capture or low-carbon electricity are much lower. Boundary stops at the gate, so it is not directly comparable with well-to-wheels rows (gasoline, diesel, jet fuel) or with per-kWh electricity rows.

Source wording. “Overall, the estimated GWP results for Case 1A and 1B are 12 and 10 kg CO2e/kg H2, respectively.”

U.S. DOE National Energy Technology Laboratory (NETL): Comparison of Commercial, State-of-the-Art, Fossil-Based Hydrogen Production Technologies (DOE/NETL-2022/3241), section 3.16.2 DOE/NETL-2022/3241, April 12, 2022
Methanol
How we define it

Methanol (CH3OH), also known as wood alcohol, as listed by AFDC in the Fuel Properties Comparison (neat methanol, M100 basis).

Energy per mass (LHV) 8,639 Btu/lb
Show details

Source wording. “Liquid Fuels | LHV: Btu/gal, Btu/lb, MJ/kg | HHV: Btu/gal, Btu/lb, MJ/kg | grams/gal. Row: Methanol 57,250 8,639 20.094 65,200 9,838 22.884 3,006”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects…
Energy per mass (HHV) 9,838 Btu/lb
Show details

Note. Source also gives 22.884 MJ/kg HHV and 20.094 MJ/kg LHV. Older table (GREET 1.8d.1, 2010); its per-gallon values (57,250 LHV and 65,200 HHV Btu/gal) equal AFDC's current ones. The 2001 DOE training module (https://www.energy.gov/documents/fcm01r0pdf, Table 1-3) lists methanol at 8,580 Btu/lb HHV and 7,760 Btu/lb LHV; it is older and was not used.

Source wording. “Liquid Fuels | LHV: Btu/gal, Btu/lb, MJ/kg | HHV: Btu/gal, Btu/lb, MJ/kg | grams/gal. Row: Methanol 57,250 8,639 20.094 65,200 9,838 22.884 3,006”

Oak Ridge National Laboratory (U.S. DOE): Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects…
Energy per volume (LHV) 57,250 Btu/gal Form: liquid at ambient conditions
Show details

Source wording. “Energy Content (higher heating value): 65,200 Btu/gal (c) | Energy Content (lower heating value): 57,250 Btu/gal (c) (Methanol column)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
Energy per volume (HHV) 65,200 Btu/gal Form: liquid at ambient conditions
Show details

Note. ORNL Transportation Energy Data Book Ed. 41 (2025), Table B.4, lists methanol at 64,600 Btu/gal gross = 56,600 Btu/gal net (slightly different; AFDC kept as primary).

Source wording. “Energy Content (higher heating value): 65,200 Btu/gal (c) | Energy Content (lower heating value): 57,250 Btu/gal (c) (Methanol column)”

U.S. DOE Alternative Fuels Data Center (AFDC): Fuel Properties Comparison Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212)
CO2 from burning 63.62 kg CO2/mmBtu
Show details

Note. Also on this page: 4.11 kg CO2 per gallon. This is the only official methanol CO2 factor found. It is a legacy figure: the EPA GHG Emission Factors Hub 2025 and EIA's current coefficients page (release Sept 18, 2024) do not list methanol. Gross (HHV) basis on EIA's own heating value (the per-gallon and per-mmBtu pair implies about 64,600 Btu/gal, which is ORNL TEDB's gross value), not AFDC's 65,200. Treated as non-biogenic because the source does not say otherwise; methanol made from biomass would differ. Not a life-cycle figure.

Source wording. “Methanol/Methanol Blends -M100 4.11 per gallon 63.62 (columns: kilograms CO2 per unit of volume; kilograms CO2 per million Btu)”

U.S. Energy Information Administration (EIA): Voluntary Reporting of Greenhouse Gases Program, Fuel Emission Coefficients, Table 2: Carbon Dioxide Emission Factors for Transportation Fuels ARCHIVED legacy page, 'Last updated January 31, 2011'; factors computed from ORNL TEDB Edition 26 (2007) density and gross heat…
Life-cycle emissions (separate measure) 91.5 g CO2e/MJ Scope: Cradle-to-grave (production plus methanol delivery, dispensing and consumption) of conventional methanol produced from natural gas, Argonne GREET 2020, per 1…
Show details

Scope. Cradle-to-grave (production plus methanol delivery, dispensing and consumption) of conventional methanol produced from natural gas, Argonne GREET 2020, per 1 MJ of methanol; GWPs of 1, 30 and 265 for CO2, CH4 and N2O

Note. Per MJ of methanol (the paper uses LHV for energy allocation; the heating-value basis of the 91.5 is not stated). Single peer-reviewed study by national-laboratory authors, not a standing DOE or EPA program value. The same paper gives a cradle-to-gate value (production only, 'does not include methanol combustion CO2 emissions') of 23.7 g CO2-eq./MJ for conventional natural-gas methanol. Not directly comparable with rows that use other boundaries or units.

Source wording. “The cradle-to-grave greenhouse gas emissions of methanol ... are 13.6, 37.9, and 84.6 g CO2-eq./MJ, respectively, compared to 91.5 g CO2-eq./MJ of conventional methanol produced from natural gas.”

Argonne National Laboratory (DOE); peer-reviewed article by Zang, Sun, Elgowainy and Wang, Environmental Science and Technology 55(8), March 2021; accepted manuscript on OSTI (ID 1807681): Technoeconomic and Life Cycle Analysis of Synthetic Methanol Production from Hydrogen and Industrial Byproduct CO2 ES&T vol. 55, issue 8, March 15, 2021 (DOI 10.1021/acs.est.0c08237); GREET 2020 model
Ammonia
How we define it

Anhydrous ammonia (NH3) used as a fuel, as described in DOE and DOE national laboratory (Oak Ridge) documents. Not listed in AFDC's Fuel Properties Comparison.

Energy per mass (LHV) 18.8 MJ/kg
Show details

Note. Source calls it 'net heat content', recorded as LHV (net heat content is the lower heating value). It is for the chemical-grade anhydrous NH3 used in the lab tests. No HHV for ammonia was found in an official source (NIST Chemistry WebBook lists no enthalpy of combustion for ammonia).

Source wording. “Table 3. Ammonia specifications. Test Value: Estimated octane number (-) > 130; Net heat content (MJ/kg) 18.8; Stoichiometric air-to-fuel ratio (-) 14.3”

Oak Ridge National Laboratory (UT-Battelle for U.S. DOE), via OSTI: Mapping Ammonia-Diesel Combustion on a Single-Cylinder 107 mm Bore Diesel Engine Retrofitted for Ammonia Port-Fuel Injection Prepublication draft, OSTI ID 3002711; file is undated (references run through December 2024)
Energy per mass (HHV) 9,670 Btu/lb
Show details

Note. Stated in an exhibit caption (cost exhibit), not in a property table. Intergovernmental cross-check in the next element: IRENA gives 22.5 MJ/kg HHV.

Source wording. “Exhibit 5-1. HHV-based ammonia fuel costs from literature used in determining the fuel cost range of this study (HHV of ammonia is 9,670 Btu/lb)”

U.S. DOE National Energy Technology Laboratory (NETL): Cooled Gas Turbine and Combined Cycle Analysis for NH3-CH4 Fuel Mixes (up to 100% NH3), Exhibit 5-1 DOE/NETL-2024/4522, October 30, 2024, report p. 43 (PDF p. 57)
CO2 from burning 0 kg CO2/mmBtu
Show details

Note. Zero CO2 at the point of use because ammonia has no carbon (a DOE statement about use, not a life-cycle figure). NOx: ORNL's engine paper (OSTI 3002711) says ammonia as an engine fuel has 'emissions challenges, including potentially high NH3, NOX, and N2O emissions'; N2O is itself a greenhouse gas. Most ammonia today is made from hydrogen from steam reforming of natural gas or other fossil fuels (ORNL), so production emissions are not captured here.

Source wording. “It can be burned directly in an internal combustion engine (ICE) with no carbon emission ... and final use in an internal combustion engine or fuel cell would produce no carbon dioxide.”

U.S. Department of Energy (Hydrogen Program): Potential Roles of Ammonia in a Hydrogen Economy February 2006
Coal (bituminous)
How we define it

Bituminous coal as the primary record, as listed by the EPA GHG Emission Factors Hub 2025, Table 1 (Stationary Combustion), group 'Coal and Coke', row 'Bituminous'. Other ranks are listed in the notes. EIA describes coal as 'a combustible black or brownish-black sedimentary rock with a high amount of carbon and hydrocarbons.'

Energy per mass (LHV) 25.8 MJ/kg Range: 19.9 to 30.5
Show details

Note. Row 'Other Bituminous Coal' (Table 1.1: steam coal, 'all bituminous coal that is not included under coking coal'). TJ/Gg = MJ/kg (exact relabel). Range = lower/upper limits of the 95% confidence interval given by the source, not a min/max of samples. NCV = LHV (IPCC Box 1.1 defines net calorific value as the lower heating value). Other ranks (value [95% CI lower, upper], TJ/Gg = MJ/kg): Anthracite 26.7 [21.6, 32.2]; Coking Coal 28.2 [24.0, 31.0] (bituminous, coke-making grade); Sub-Bituminous Coal 18.9 [11.5, 26.0]; Lignite 11.9 [5.50, 21.6]. Table 1.2 does not state a moisture basis for the coal values.

Source wording. “Net calorific value (TJ/Gg) Lower Upper ... Other Bituminous Coal 25.8 19.9 30.5”

IPCC National Greenhouse Gas Inventories Programme: 2006 IPCC Guidelines for National Greenhouse Gas Inventories, Volume 2 Energy, Chapter 1, Table 1.2 2006 Guidelines (the 2019 Refinement's Chapter 1 does not restate this table)
Energy per mass (HHV) 24.93 mmBtu/short ton
Show details

Note. Default heat content (HHV) per EPA Hub Table 1; the Hub says 'If heat content is available from the fuel supplier, it is preferable to use that value. If not, default heat contents are provided.' Other ranks in the same table, Heat Content (HHV) in mmBtu per short ton, names exactly as printed by EPA: Anthracite 25.09; Sub-bituminous 17.25; Lignite 14.21. (The table also has rows 'Mixed (Commercial Sector)', 'Mixed (Electric Power Sector)', 'Mixed (Industrial Coking)', 'Mixed (Industrial Sector)' and 'Coal Coke', not listed here.) EIA's 'Carbon Dioxide Emissions Coefficients' page names the ranks 'Anthracite', 'Bituminous', 'Subbituminous', 'Lignite' but prints CO2 per short ton and per million Btu only, not heat content. The same default heat contents (Anthracite 25.09, Bituminous 24.93, Subbituminous 17.25, Lignite 14.21 mmBtu/short ton) appear in 40 CFR Part 98 Table C-1 (eCFR, read 2026-11-13), which is the Hub's stated source.

Source wording. “Table 1 Stationary Combustion, 'Coal and Coke': Fuel Type 'Bituminous' | Heat Content (HHV), mmBtu per short ton: 24.93 | CO2 Factor, kg CO2 per mmBtu: 93.28”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
CO2 from burning 93.28 kg CO2/mmBtu
Show details

Note. Combustion (stack) CO2 only; the Hub states 'The factors represented in the table above represent combustion emissions only and do not represent upstream emissions.' Same HHV basis as the energy value. Other ranks in the same EPA table, CO2 Factor in kg CO2 per mmBtu: Anthracite 103.69; Sub-bituminous 97.17; Lignite 97.72. Second authoritative source, slightly different for bituminous: EIA 'Carbon Dioxide Emissions Coefficients' (Release Date: September 18, 2024; https://www.eia.gov/environment/emissions/co2_vol_mass.php), 'Coals by type' row printed as 'Bituminous | 5,124.76 short ton | 2,324.56 short ton | 205.57 | 93.24' (lb CO2/short ton, kg CO2/short ton, lb CO2/million Btu, kg CO2/million Btu), i.e. 93.24 kg CO2/mmBtu vs EPA 93.28. EIA's other ranks (kg CO2/million Btu, names as printed): Anthracite 103.69; Subbituminous 97.13; Lignite 98.27. EIA says its carbon factors are provided by EPA, Inventory of U.S. Greenhouse Gas Emissions and Sinks: 1990-2022.

Source wording. “Table 1 Stationary Combustion, 'Coal and Coke': Fuel Type 'Bituminous' | Heat Content (HHV), mmBtu per short ton: 24.93 | CO2 Factor, kg CO2 per mmBtu: 93.28 | kg CO2 per short ton: 2325”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Life-cycle emissions (separate measure) 820 g CO2e/kWh Range: 740 to 910 Scope: Lifecycle emissions of electricity generated by pulverized coal (PC) power plants (direct emissions, infrastructure and supply chain emissions, and methane…
Show details

Scope. Lifecycle emissions of electricity generated by pulverized coal (PC) power plants (direct emissions, infrastructure and supply chain emissions, and methane emissions), IPCC AR5 WGIII Annex III; value is the median of the literature, range is its min to max

Note. Per kWh of electricity generated from coal, NOT per MJ of coal burned; the figure describes coal-fired power, so it is not directly comparable with per-MJ fuel rows or with any row using a different boundary. Source column 'Direct emissions' (stack CO2) is 670 / 760 / 870 g CO2eq/kWh (min/median/max) and is a different metric. PDF opened via direct download; ipcc.ch returns HTTP 403 to some automated fetchers.

Source wording. “Coal - PC | Direct emissions 670 / 760 / 870 | Infrastructure & supply chain 9.6 | Biogenic 0 | Methane 47 | Lifecycle emissions (incl. albedo effect) Min / Median / Max: 740 / 820 / 910”

IPCC (Intergovernmental Panel on Climate Change): Climate Change 2014: Mitigation of Climate Change (AR5 WGIII), Annex III: Technology-specific Cost and Performance Parameters, Table A.III.2 'Emissions of selected electricity supply technologies (gCO2eq/kWh)' AR5 WGIII Annex III, 2014, Table A.III.2, p. 1335
Wood (dry)
How we define it

'Wood and Wood Residuals' as listed under 'Biomass Fuels - Solid' in the EPA GHG Emission Factors Hub 2025, Table 1 (Stationary Combustion). EIA describes wood and wood waste as 'bark, sawdust, wood chips, wood scrap, and paper mill residues'; firewood is burned as cord wood and pellets.

Energy per mass (LHV) 15.6 MJ/kg Range: 7.9 to 31
Show details

Note. MOISTURE: the source states NO moisture condition for this value (not in the table row, not in footnote 9 'EFDB; uncertainty range: expert judgement', not in the surrounding text, which only says wood/bark NCV-to-GCV conversions are in the WRI/WBCSD Pulp and Paper tools). Row is 'Wood/Wood Waste' (solid biofuels). Range = 95% confidence interval limits. TJ/Gg = MJ/kg. Same table: Other Primary Solid Biomass 11.6 [5.90, 23.0]; Charcoal 29.5 [14.9, 58.0]. For wood with an explicitly stated moisture basis see the two alt elements below (ORNL, dry basis).

Source wording. “Wood/Wood Waste 9 15.6 7.90 31.0 ... 9 EFDB; uncertainty range: expert judgement”

IPCC National Greenhouse Gas Inventories Programme: 2006 IPCC Guidelines for National Greenhouse Gas Inventories, Volume 2 Energy, Chapter 1, Table 1.2 2006 Guidelines (the 2019 Refinement's Chapter 1 does not restate this table)
Energy per mass (HHV) 17.48 mmBtu/short ton
Show details

Note. MOISTURE BASIS: DRY. The Hub table does not print a moisture basis, but its stated source, 40 CFR Part 98 Table C-1 (eCFR, read 2026-11-13; table last amended 81 FR 89252, Dec. 9, 2016), prints the same row as 'Wood and Wood Residuals (dry basis) | 17.48 | 93.80' with footnote 5: 'Use the following formula to calculate a wet basis HHV for use in Equation C-1: HHVw = ((100 - M)/100)*HHVd where HHVw = wet basis HHV, M = moisture content (percent) and HHVd = dry basis HHV from Table C-1.' So this is not an as-received (wet) figure; wood with moisture has less energy per ton. Default value for emissions reporting, not a measured value for a specific wood. EIA's Btu page prints a separate figure per cord (see energy_per_volume).

Source wording. “Table 1 Stationary Combustion, 'Biomass Fuels - Solid': Fuel Type 'Wood and Wood Residuals' | Heat Content (HHV), mmBtu per short ton: 17.48 | CO2 Factor, kg CO2 per mmBtu: 93.8”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
CO2 from burning 93.8 kg CO2/mmBtu Biogenic CO2 (reported separately by the EPA)
Show details

Note. Biogenic CO2 from burning biomass; nothing is subtracted or netted here. The Hub lists the row under 'Biomass Fuels - Solid' and does not itself use the word 'biogenic' in Table 1; EPA's guidance document that the Hub points to ('Greenhouse Gas Inventory Guidance: Direct Emissions from Stationary Combustion Sources', https://www.epa.gov/sites/default/files/2020-12/documents/stationaryemissions.pdf, section 1.2) says CO2 from biomass combustion is reported 'as biomass CO2 emissions (in terms of total amount of biogenic CO2 emitted)' and tracked separately from fossil CO2. Per mmBtu on the same dry-basis HHV as the energy value. The same 93.80 kg CO2/mmBtu appears in 40 CFR Part 98 Table C-1 under 'Biomass fuels-solid'. Combustion only; the Hub states its factors 'do not represent upstream emissions.'

Source wording. “Table 1 Stationary Combustion, 'Biomass Fuels - Solid': Fuel Type 'Wood and Wood Residuals' | Heat Content (HHV), mmBtu per short ton: 17.48 | CO2 Factor, kg CO2 per mmBtu: 93.8 | kg CO2 per short ton: 1640”

U.S. EPA, Center for Corporate Climate Leadership: GHG Emission Factors Hub, Table 1 Stationary Combustion 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub,…
Grid electricity (reference)
How we define it

Reference item, not a fuel: average U.S. grid electricity, using EIA's CO2 emissions factor for total electricity generation by the U.S. electric power industry (national average generation mix), from EIA State Electricity Profiles, 'United States Electricity Profile 2024', Table 1. EIA defines electricity as 'the flow of electrical power or charge' and as a secondary energy source.

CO2 from burning 0.785 lb CO2/kWh
Show details

Note. DATA YEAR 2024 (most recent full year published by EIA as of 2026-11-13). This is generation-side combustion CO2 emitted at power plants for the national-average U.S. mix (total electricity generation by the electric power industry), NOT a life-cycle figure. EIA prints it in pounds per MWh (785). EIA's FAQ says 'The factors are in pounds of CO2 per megawatthour (MWh). Divide the factors by 1,000 to convert the factor to pounds per kWh', so 0.785 lb CO2/kWh is an exact relabeling of the printed value. EIA treats electricity from biomass, hydro, solar and wind as carbon neutral (FAQ id=74). Other figures found, different year/method, not reconciled: (a) EIA FAQ 'How much carbon dioxide is produced per kilowatthour of U.S. electricity generation?' (https://www.eia.gov/tools/faqs/faq.php?id=74&t=11, last updated December 11, 2024) prints 'about 0.81 pounds of CO2 emissions per kWh' for 2023 utility-scale plants (1.53 billion metric tons CO2, about 4.18 trillion kWh); (b) EPA eGRID2023 'US Average' Total Output Emission Factor, shown in EPA GHG Emission Factors Hub 2025 Table 6, is 771.523 lb CO2/MWh (2023 data; EPA eGRID page lists eGRID2023 as latest). ENERGY DEFINITION: EIA, 'Units and calculators explained: British thermal units (Btu)', table 'Sample Btu conversion factors' (https://www.eia.gov/energyexplained/units-and-calculators/british-thermal-units.php): 'Electricity | 1 kilowatthour=3,412 Btu'. EIA Monthly Energy Review, October 2026, Appendix B (https://www.eia.gov/totalenergy/data/monthly/pdf/sec12.pdf) calls it 'the constant conversion factor representing the heat content of electricity-3,412 Btu per kWh'.

Source wording. “Table 1. 2024 Summary statistics (United States) ... Net generation (megawatthours) 4,308,634,297 ... Carbon Dioxide (thousand metric tons) 1,537,073 ... Carbon Dioxide (lbs/MWh) 785”

U.S. Energy Information Administration (EIA): State Electricity Profiles: United States Electricity Profile 2024, Table 1. 2024 Summary statistics Data year 2024. Page header: 'Data for: 2024 | Release Date: November 10, 2025 | Next Release: November 2026' (the 2025 data had…

Source register

Every source used in the table above, with the edition we read and the day we checked it.

  1. U.S. Energy Information Administration (EIA). Energy Explained: Sources of energy. Undated web page, read 2026-11-13. Checked .
  2. U.S. Energy Information Administration (EIA). Energy Explained: Gasoline. Undated web page, read 2026-11-13. Checked .
  3. U.S. DOE Alternative Fuels Data Center (AFDC). Fuel Properties Comparison. Live table read 2026-11-13; same values as the March 2024 PDF edition (DOE/GO-102024-6212). Checked .
  4. U.S. Department of Energy, Office of Critical Minerals and Energy Innovation. Guidelines To Determine Life Cycle Greenhouse Gas Emissions of Clean Transportation Fuel Production Pathways Using 45ZCF-GREET, Table 1. Rev. September 2026, Table 1. Checked .
  5. U.S. EPA, Center for Corporate Climate Leadership. GHG Emission Factors Hub, Table 1 Stationary Combustion. 2025 edition, Last Modified January 15, 2025 (EPA's Hub page, https://www.epa.gov/climateleadership/ghg-emission-factors-hub, still lists this as the current edition). Checked .
  6. U.S. Environmental Protection Agency, Office of Transportation and Air Quality. Summary Lifecycle Analysis Greenhouse Gas Results for the U.S. Renewable Fuels Standard Program. May 2023 (v1.1, April 2023 update); current file linked from the EPA page as of 2026-11-13. Checked .
  7. U.S. Energy Information Administration (EIA). Energy Explained: Diesel fuel. Undated web page, read 2026-11-13. Checked .
  8. IPCC National Greenhouse Gas Inventories Programme. 2006 IPCC Guidelines for National Greenhouse Gas Inventories, Volume 2 Energy, Chapter 1, Table 1.2. 2006 Guidelines (the 2019 Refinement's Chapter 1 does not restate this table). Checked .
  9. U.S. Energy Information Administration (EIA). Monthly Energy Review, Glossary. Monthly Energy Review glossary file, September 2026 edition (file created 2026-09-29). Checked .
  10. U.S. Department of Energy (DOE/EE-2365). Sustainable Aviation Fuel: Reducing Emissions from Commercial Flight (fact sheet), figure 'Life Cycle Greenhouse Gas Emissions of SAFs in GREET', footnote a. DOE/EE-2365, September 2024. Checked .
  11. U.S. DOE Alternative Fuels Data Center (AFDC). Ethanol Fuel Basics. Web page, no date shown; read 2026-11-13. Checked .
  12. Oak Ridge National Laboratory (U.S. DOE). Biomass Energy Data Book, Appendix A: Lower and Higher Heating Values of Gas, Liquid and Solid Fuels. Biomass Energy Data Book 2011 (as printed on the table). Archived copy of the original cta.ornl.gov URL (ORNL site now redirects to tedb.ornl.gov). Checked .
  13. U.S. DOE Alternative Fuels Data Center (AFDC). Biodiesel Fuel Basics. Web page, no date shown; read 2026-11-13. Checked .
  14. U.S. Energy Information Administration (EIA). Energy Explained: Use of natural gas. Last updated October 31, 2024 (2023 data, preliminary). Checked .
  15. U.S. DOE Alternative Fuels Data Center (AFDC). Natural Gas Basics. Undated web page, read 2026-11-13. Checked .
  16. U.S. Energy Information Administration (EIA). Energy Explained: Liquefied natural gas. Last updated June 21, 2024 (Natural Gas Monthly, March 2024). Checked .
  17. U.S. Energy Information Administration (EIA). Energy Explained: Uses of hydrocarbon gas liquids. Last updated December 26, 2023. Checked .
  18. U.S. Department of Energy (Hydrogen and Fuel Cell Technologies / Clean Energy Manufacturing). Hydrogen Fuel Basics. Page last updated October 9, 2026 (redirected from energy.gov/eere/fuelcells/hydrogen-fuel-basics). Checked .
  19. U.S. DOE Alternative Fuels Data Center (AFDC). Hydrogen Basics. Web page, no date shown ('As of 2024' station counts); read 2026-11-13. Checked .
  20. U.S. Energy Information Administration (EIA). Hydrogen explained. Web page, no date shown; read 2026-11-13. Checked .
  21. U.S. EPA, Office of Air and Radiation. Hydrogen in Combustion Turbine Electric Generating Units, Technical Support Document. May 23, 2023. Checked .
  22. U.S. DOE National Energy Technology Laboratory (NETL). Comparison of Commercial, State-of-the-Art, Fossil-Based Hydrogen Production Technologies (DOE/NETL-2022/3241), section 3.16.2. DOE/NETL-2022/3241, April 12, 2022. Checked .
  23. U.S. DOE Alternative Fuels Data Center (AFDC). Methanol. Web page, no date shown; read 2026-11-13. Checked .
  24. U.S. Energy Information Administration (EIA). Voluntary Reporting of Greenhouse Gases Program, Fuel Emission Coefficients, Table 2: Carbon Dioxide Emission Factors for Transportation Fuels. ARCHIVED legacy page, 'Last updated January 31, 2011'; factors computed from ORNL TEDB Edition 26 (2007) density and gross heat of combustion. Checked .
  25. Argonne National Laboratory (DOE); peer-reviewed article by Zang, Sun, Elgowainy and Wang, Environmental Science and Technology 55(8), March 2021; accepted manuscript on OSTI (ID 1807681). Technoeconomic and Life Cycle Analysis of Synthetic Methanol Production from Hydrogen and Industrial Byproduct CO2. ES&T vol. 55, issue 8, March 15, 2021 (DOI 10.1021/acs.est.0c08237); GREET 2020 model. Checked .
  26. Oak Ridge National Laboratory (UT-Battelle for U.S. DOE), via OSTI. Mapping Ammonia-Diesel Combustion on a Single-Cylinder 107 mm Bore Diesel Engine Retrofitted for Ammonia Port-Fuel Injection. Prepublication draft, OSTI ID 3002711; file is undated (references run through December 2024). Checked .
  27. U.S. Department of Energy (Hydrogen Program). Potential Roles of Ammonia in a Hydrogen Economy. February 2006. Checked .
  28. U.S. Energy Information Administration (EIA). Coal explained: What is coal?. Last updated: October 24, 2023, with data available at the time of update (page text: 'Coal is classified as a nonrenewable energy source because it takes millions of years to form.'). Checked .
  29. IPCC (Intergovernmental Panel on Climate Change). Climate Change 2014: Mitigation of Climate Change (AR5 WGIII), Annex III: Technology-specific Cost and Performance Parameters, Table A.III.2 'Emissions of selected electricity supply technologies (gCO2eq/kWh)'. AR5 WGIII Annex III, 2014, Table A.III.2, p. 1335. Checked .
  30. U.S. Energy Information Administration (EIA). Biomass explained. No revision date shown on the page; read 2026-11-13 (page text: 'Biomass is renewable organic material that comes from plants and animals.'). Checked .
  31. U.S. Energy Information Administration (EIA). Biomass explained: Wood and wood waste. No revision date shown on the page; cites Monthly Energy Review, May 2026 (2025 data preliminary). Checked .
  32. U.S. Energy Information Administration (EIA). Electricity explained: What is electricity?. No revision date shown on the page; read 2026-11-13 (page text: 'Primary energy sources are renewable or nonrenewable energy, but the electricity we use is neither renewable nor nonrenewable.'). Checked .
  33. U.S. Energy Information Administration (EIA). State Electricity Profiles: United States Electricity Profile 2024, Table 1. 2024 Summary statistics. Data year 2024. Page header: 'Data for: 2024 | Release Date: November 10, 2025 | Next Release: November 2026' (the 2025 data had not been published when read on 2026-11-13). Checked .
  34. Oak Ridge National Laboratory (U.S. DOE). Transportation Energy Data Book, Appendix B, Table B.4 Heat Content for Various Fuels. Edition 41 (2025), ORNL/TM-2026/4560, p. B-4 (current edition per tedb.ornl.gov). Checked .
  35. Oak Ridge National Laboratory (U.S. DOE). Biomass Energy Data Book: Edition 4, Appendix A, Table A.1 Lower and Higher Heating Values of Gas, Liquid and Solid Fuels. Edition 4, ORNL/TM-2011/446, September 2011 (latest edition), PDF p. 201. Checked .
  36. U.S. DOE National Energy Technology Laboratory (NETL). Cooled Gas Turbine and Combined Cycle Analysis for NH3-CH4 Fuel Mixes (up to 100% NH3), Exhibit 5-1. DOE/NETL-2024/4522, October 30, 2024, report p. 43 (PDF p. 57). Checked .