Cetane Number: Diesel's Version of Octane
Cetane number rates how quickly a diesel fuel ignites after it is sprayed into hot, compressed air. A higher number means a shorter wait between injection and ignition. That makes it the mirror image of octane, which rates how well gasoline resists igniting.
Both are laboratory scores, and both are often mistaken for quality or energy rankings. Below you will find what cetane number measures, a side-by-side with octane, the values and minimums that appear in specifications, and why a fuel can rate high on cetane while holding less energy per gallon.
What cetane number measures
A diesel engine has no spark plug. It compresses air until the air is hot, then injects fuel, which must ignite by itself. A Sandia National Laboratories paper calls the time between the start of injection and ignition the ignition delay. Fuels with short delays get higher cetane numbers, and fuels with long delays get lower ones. The mechanics are covered in how diesel engines ignite fuel.
The score matters because ignition timing shapes how the engine runs. The Sandia authors write that high-cetane fuels help cold starting and give quieter operation. The National Renewable Energy Laboratory (NREL) guide to biodiesel treats cetane number as a gauge of ignition quality and ties it to white smoke, cold starting and combustion roughness.
The standard test method, ASTM D613, uses a single-cylinder test engine with an adjustable compression ratio, run at 900 rpm, according to the Sandia paper. Test devices with a constant-volume chamber are also in use and report a "derived cetane number" that is calibrated against the engine results.
Cetane versus octane
Octane and cetane describe the same event, a fuel igniting by itself, but gasoline engines want to avoid it and diesel engines depend on it. The Alternative Fuels Data Center (AFDC), a Department of Energy resource, lists a range for each.
| Feature | Octane number | Cetane number |
|---|---|---|
| Engine it serves | Spark-ignition (gasoline) | Compression-ignition (diesel) |
| What a high number means | Fuel resists self-ignition longer | Fuel ignites sooner after injection |
| Trouble it relates to | Knock | Cold starts, white smoke, rough combustion |
| Range listed by AFDC | 84 to 93 (pump gasoline/E10) | 40 to 55 (diesel) |
| Natural gas (Sandia) | Typically above 110 | Typically below 0 |
The natural gas row shows the opposition clearly. The Sandia paper reports that natural gas typically has a very low cetane number and a high octane number, so the two scores pull in opposite directions. The gasoline side is explained in octane rating explained. Diesel, in the definition used by the U.S. Energy Information Administration (EIA), is distillate fuel oil sold for vehicles with compression-ignition engines.
Typical values and minimums
AFDC lists a cetane range of 40 to 55 for low-sulfur diesel, 45 to 65 for biodiesel and 70 to 85 for renewable diesel. The Sandia paper gives a similar picture: U.S. cetane numbers run from 40 to the mid 50s, and the minimum acceptable value is 40 under ASTM specifications but 51 under the European CEN specification.
Biodiesel has its own floor. The NREL guide reports that ASTM D6751 sets a minimum of 45 for neat biodiesel (B100). A specification sets a floor rather than a target, so fuels in the market vary above it. The Sandia authors single out cetane number and aromatic content as two properties that vary quite a bit in the market.
Conditions matter too. A footnote in the NREL guide says low ambient temperatures and operation at high altitude may call for fuels with higher cetane ratings.
Three related terms are easy to confuse:
- Cetane number is measured in an engine test.
- Derived cetane number comes from a constant-volume chamber and is calibrated against the engine test.
- Cetane index is a calculation from density and boiling-range data, not a measurement of ignition. The NREL glossary says it is widely mistaken for cetane number and is not valid for biodiesel or biodiesel blends.
A fuel's cetane number can also be raised with an additive called a cetane improver. The Sandia paper names 2-ethylhexyl nitrate and di-tert-butyl peroxide as the most common ones, used in tens to hundreds of parts per million. Sulfur content is a separate specification, covered in ultra-low sulfur diesel explained.
Cetane and energy content
A fast-igniting fuel is not automatically an energy-rich one. Ignition quality describes timing. Energy per gallon describes how much heat the fuel releases.
| Fuel | Cetane number | Energy per gallon (LHV) |
|---|---|---|
| Diesel (AFDC low-sulfur column) | 40 to 55 | 128,488 Btu/gal (35.81 MJ/L) |
| Biodiesel (B100) | 45 to 65 | 119,550 Btu/gal (33.32 MJ/L) |
The arithmetic: 119,550 รท 128,488 = 0.93. A gallon of B100 holds about 7 percent less energy than a gallon of diesel, even though AFDC lists a higher cetane range for it. For how density changes the picture, see energy density by mass and volume, or compare diesel and biodiesel directly. AFDC defines B100 as pure, or neat, biodiesel, and says it fuels compression-ignition engines like petroleum diesel does. How it differs from renewable diesel is the subject of biodiesel vs renewable diesel.
Common mistakes
- Treating cetane as octane for diesel. The two scales point in opposite directions. A high octane number means a fuel resists igniting, and a high cetane number means it ignites readily.
- Assuming higher cetane means more energy. Biodiesel lists a higher range than diesel and carries less energy per gallon.
- Confusing cetane index with cetane number. The index is calculated, and the NREL glossary warns it does not work for biodiesel or biodiesel blends.
- Assuming biodiesel ignites poorly. AFDC lists 45 to 65 for it, and the NREL guide gives 45 as the ASTM floor for B100, compared with a floor of 40 for conventional diesel.
- Expecting one minimum everywhere. The Sandia paper contrasts a minimum of 40 under ASTM specifications with 51 under European ones.
Frequently asked questions
What is a good cetane number for diesel?
Under ASTM specifications the minimum is 40, and the Sandia paper puts U.S. diesel at 40 to the mid 50s. AFDC lists 40 to 55. European specifications ask for at least 51. What counts as good depends on the engine and conditions, since cold weather and high altitude may call for a higher rating.
How is cetane number measured?
ASTM D613 uses a single-cylinder test engine with an adjustable compression ratio, run at 900 rpm, and compares the fuel's ignition delay with reference fuels. A faster method burns a small sample in a constant-volume chamber and reports a derived cetane number calibrated against the engine results, according to the Sandia paper.
Does biodiesel have a higher cetane number than petroleum diesel?
AFDC lists a higher range for biodiesel, 45 to 65, than for diesel, 40 to 55, and the NREL guide gives 45 as the ASTM minimum for B100. The ranges overlap, so a particular batch of diesel can rate above a particular batch of biodiesel. The NREL guide notes that renewable diesel typically has a very high cetane number.
Why would cold weather or altitude change the cetane a diesel needs?
A footnote in the NREL guide says low ambient temperatures and operation at high altitude may require fuels with higher cetane ratings. The Sandia authors add that high-cetane fuels ease engine cold starting. Neither source gives a single threshold, so the engine maker's guidance and the fuel supplier's grade for the season are the practical references.
Sources
- Biodiesel Handling and Use Guide: Sixth Edition: National Renewable Energy Laboratory, via the Office of Scientific and Technical Information. Accessed November 13, 2026.
- Fuel Properties Comparison: Alternative Fuels Data Center, U.S. Department of Energy. Accessed November 13, 2026.
- Fuels and the Impact of Fuel Composition on Engine Performance: Sandia National Laboratories, via the Office of Scientific and Technical Information. Accessed November 13, 2026.
- Biodiesel Fuel Basics: Alternative Fuels Data Center, U.S. Department of Energy. Accessed November 13, 2026.
- Diesel fuel explained: U.S. Energy Information Administration (EIA). Accessed November 13, 2026.
Spotted something wrong or out of date? Tell us through the corrections page. We answer within 10 business days.