Fossil fuels

Jet Fuel Explained: Jet A, Jet A-1 and Kerosene

Beautiful view from an airplane wing against a sunset sky, creating a tranquil travel moment
Photo by photoGraph on Pexels. A general illustration, not evidence for any number.

Jet fuel is a kerosene-type petroleum fuel for turbine aircraft engines, taken from the middle of the crude oil distillation range. Jet A and Jet A-1 are its two main grades. A fuel-quality report hosted by the U.S. Federal Aviation Administration (FAA) says the only difference between them is the freezing point: Jet A has a maximum of -40°C (-40°F) and Jet A-1 a maximum of -47°C (-53°F).

"Kerosene" can mean several products, and jet fuel is not ordinary kerosene sold under a new name. It has to meet a long list of limits written into ASTM D1655, the standard for aviation turbine fuel. This article explains what the fuel is, what that standard limits, how jet fuel lines up against diesel on the Comparator's numbers, and which other grades exist. How refineries make the kerosene cut is covered in how crude oil is refined.

What jet fuel is

The U.S. Energy Information Administration (EIA) defines kerosene-type jet fuel as a kerosene-based product used in commercial and military turbojet and turboprop aircraft engines. In EIA's 2022 figures it was the fourth-most-used petroleum product in the United States, about 8% of petroleum consumption, or roughly 65 million gallons a day.

The Intergovernmental Panel on Climate Change (IPCC) calls jet kerosene a medium distillate with the distillation characteristics and flash point of kerosene, boiling between 150 and 300°C (302 and 572°F). The same IPCC definition adds that jet kerosene carries particular specifications, freezing point among them. The FAA-hosted report describes jet fuel as a mixture of as many as thousands of different hydrocarbon molecules, mostly with 9 to 16 carbon atoms, and says the specification is written as performance requirements, not as a fixed recipe.

Jet A and Jet A-1: one number apart

ASTM D1655 covers both grades. According to the FAA-hosted report, Jet A is the most prevalent jet fuel in the United States and Jet A-1 is used in most of the rest of the world. Most, not all: neither grade is confined to one set of borders.

Freezing point has a precise meaning here. In the FAA-hosted report's description of the lab tests, a fuel sample is cooled until hydrocarbon crystals appear, then warmed slowly, and the temperature at which the last crystals disappear is the freezing point. The crystals matter because the report notes that they can block fuel lines, filters and nozzles, and the fuel has to keep flowing through long cruise periods at altitude. A lower limit leaves more margin against that.

The limit is a ceiling, not a target. The specification table lists the freezing point as a maximum, so a batch passes if it freezes at or below -40°C (Jet A) or -47°C (Jet A-1).

Selected ASTM D1655 limits as quoted in a 2014 FAA-hosted report.
PropertyLimit
Freezing pointJet A: -40°C (-40°F) max; Jet A-1: -47°C (-53°F) max
Flash point38°C (100°F) min
Density at 15°C775 to 840 kg/m³ (about 6.5 to 7.0 lb/gal)
Distillation10% recovered at 205°C (401°F) max; final boiling point 300°C (572°F) max
Net heat of combustion42.8 MJ/kg (18,400 Btu/lb) min
Aromatics25% by volume max
Total sulfur0.30% by mass max

The standard is revised from time to time, so check the current edition for exact limits. Two entries deserve a comment. The heat-of-combustion floor of 42.8 MJ/kg is a net (lower) heating value, the same basis as the Comparator's mass figure. And the sulfur ceiling of 0.30% by mass equals 3,000 ppm (0.30 × 10,000). It is a limit for a different fuel than the 15 ppm cap in ultra-low-sulfur diesel, and a ceiling, not a typical level.

Jet fuel and diesel on the Comparator's numbers

Jet fuel and diesel come from neighboring parts of the distillation range, so they are close in energy. Compare jet fuel and diesel in the Comparator for the full record.

Jet fuel and diesel on the Comparator's figures. Mass is on an LHV basis; volume is shown on both bases, and each row compares like with like.
PropertyJet fuelDiesel
Energy per kg, LHV44.1 MJ/kg (18,960 Btu/lb)43 MJ/kg (18,487 Btu/lb)
Energy per liter, LHV35.7 MJ/L (128,100 Btu/gal)35.81 MJ/L (128,488 Btu/gal)
Energy per liter, HHV37.63 MJ/L (135,000 Btu/gal)38.6 MJ/L (138,490 Btu/gal)
CO2 from burning, per energy68.45 g/MJ (72.22 kg per million Btu)70.1 g/MJ (73.96 kg per million Btu)

Per kilogram on an LHV basis, jet fuel holds about 2.6% more (44.1 ÷ 43.0 = 1.026). Per gallon the gap depends on the basis: about 0.3% less on LHV (128,100 ÷ 128,488 = 0.997) and about 2.5% less on HHV (135,000 ÷ 138,490 = 0.975). Per unit of energy, the U.S. Environmental Protection Agency (EPA) lists jet fuel about 2.3% lower in CO2 from burning (72.22 ÷ 73.96 = 0.977). Per gallon, EPA's factors are 9.75 kg for jet fuel and 10.21 kg for diesel.

Treat the per-kilogram gap with care. IPCC's published ranges, 42.0 to 45.0 MJ/kg for jet kerosene and 41.4 to 43.3 MJ/kg for gas/diesel oil, overlap. The volume figures also come from different sources: EPA (HHV) and the Oak Ridge National Laboratory Transportation Energy Data Book (LHV) for jet fuel, and the Alternative Fuels Data Center (AFDC) for diesel. Because the two bases give different gaps, treat the per-gallon difference as small and uncertain. All CO2 values here count burning only. Gasoline vs diesel fuel does the same side-by-side for the road fuels.

Other grades and blends you may meet

Jet A and Jet A-1 are the kerosene grades. The FAA-hosted report notes that a Canadian standard covers a wide-cut fuel, Jet B, used in parts of Canada and Alaska, and that another covers military grades JP-5 and JP-8. IPCC's separate "jet gasoline" category covers a lighter turbine fuel, a blend of kerosene with gasoline or naphtha that distills between 100 and 250°C (212 and 482°F).

Sustainable aviation fuel (SAF) enters through blending. AFDC says SAF must be blended with Jet A before use, with limits between 10% and 50% depending on feedstock and production method, and 5% for co-processing at a refinery. How SAF and other synthetic fuels are made is the subject of synthetic fuels and e-fuels.

Common mistakes

  • Treating Jet A and Jet A-1 as unrelated fuels. The FAA-hosted report names the freezing-point limit as the one difference between them.
  • Equating jet fuel with plain kerosene. IPCC lists jet kerosene separately because it carries extra specifications, and the fuel must meet D1655.
  • Picturing the freezing point as ice. The FAA-hosted report ties it to hydrocarbon crystals, mainly wax from straight-chain paraffins, and treats water and ice as a separate contamination issue.
  • Calling jet fuel relabeled diesel. The cuts are neighbors, but the specifications differ, including the sulfur ceiling: 0.30% by mass for jet fuel and 15 ppm for ultra-low-sulfur diesel.
  • Assuming it carries far more energy than diesel. The Comparator's per-kilogram gap is about 2.6%, inside the overlap of the published ranges.
  • Expecting a hard border between grades. The FAA-hosted report says "most prevalent" and "most of the rest of the world," not "only."

Frequently asked questions

What is the difference between Jet A and Jet A-1?

The freezing-point limit. Jet A may freeze at up to -40°C (-40°F) and Jet A-1 at up to -47°C (-53°F), according to the FAA-hosted report on ASTM D1655. Jet A is the most common grade in the United States, and Jet A-1 is used in most of the rest of the world.

Is jet fuel the same as kerosene?

It is kerosene-based, but not interchangeable with every kerosene product. IPCC defines jet kerosene as a medium distillate with kerosene's distillation range and flash point plus added specifications such as freezing point. EIA describes the fuel as kerosene-based.

Why does jet fuel have a freezing-point limit?

Wax crystals that form in cold fuel can block lines, filters and nozzles, and aircraft engines must keep receiving fuel during long flights at altitude. The same report says freezing point depends on molecular makeup, and that normal (straight-chain) paraffins crystallize first.

How much CO2 does burning jet fuel release?

EPA lists 72.22 kg of CO2 per million Btu, which is 68.45 g per MJ, or 9.75 kg (about 21.5 lb) per gallon. That counts burning only. It excludes producing and delivering the fuel, which a life-cycle measure would add.

Sources

Spotted something wrong or out of date? Tell us through the corrections page. We answer within 10 business days.