Synthetic Fuels and E-Fuels: How They Are Made
A synthetic fuel is a fuel built by chemical reactions from simple ingredients, usually a source of carbon plus hydrogen, instead of being refined from crude oil. An e-fuel (short for electrofuel) is the version in which the hydrogen comes from splitting water with electricity and the carbon comes from captured carbon dioxide (CO2).
The word "synthetic" describes the route, not the product. Natural gas, biomass or captured CO2 can all be turned into the same jet-range hydrocarbons, and the product can be hard to tell from its petroleum counterpart. What differs is the starting material, and with it the emissions story. This article follows the steps from raw ingredients to finished fuel, then works through one published case to show how much the inputs matter.
The building blocks: hydrogen, carbon and a gas called syngas
Every synthesis route needs two elements and energy. Hydrogen is one, and for e-fuels it comes from electrolysis, the process described in hydrogen as a fuel. Carbon is the other. It can come from natural gas, from gasified biomass, or from CO2 captured at an industrial plant or from the air.
Many routes pass through syngas, a mixture of carbon monoxide (CO) and hydrogen. The name reflects its use as a starting point for synthesizing fuels and other chemicals, including methanol and ammonia, according to the National Energy Technology Laboratory (NETL). When the carbon source is CO2, the CO has to be made first. A reaction called the reverse water-gas shift does that: CO2 plus hydrogen gives CO plus water. Argonne National Laboratory's model of one e-fuel route runs this step at about 600 °C.
In the language of Argonne's authors, e-fuels are synthetic hydrocarbons produced from water and waste CO2 streams, with zero-carbon electricity as the main energy source. That is a narrower idea than "synthetic fuel," which also covers fuel made from fossil gas.
Two main routes: Fischer-Tropsch and methanol
| Route | Carbon and hydrogen source | Key steps | Typical products |
|---|---|---|---|
| Gas-to-liquids by Fischer-Tropsch (FT) | Natural gas | Reform gas to syngas, run FT synthesis, upgrade by hydrocracking | Jet-range fuel, naphtha, propane and butane |
| Biomass FT | Gasified woody biomass | Gasify to syngas, then FT synthesis | Jet fuel |
| E-methanol | Captured CO2 and electrolytic hydrogen | Reverse water-gas shift, then methanol synthesis | Methanol |
| CO2-based FT | Captured CO2 and electrolytic hydrogen | Make syngas from CO2 and hydrogen, then FT | Hydrocarbon fuels |
Fischer-Tropsch (FT) synthesis is the older of the two routes. NETL says the technology reaches back to the 1920s and was first used where conventional fuels were scarce or natural gas was stranded far from markets. In the gas-to-liquids plant design NETL evaluated, syngas with a hydrogen-to-CO ratio of about 2 flows over a cobalt catalyst, and the reaction produces a mix of hydrocarbons from methane up to chains of more than 100 carbon atoms. A second stage, hydrocracking, breaks the long chains into the range wanted for jet fuel, about 8 to 16 carbon atoms, and separates lighter naphtha and propane and butane. NETL describes gas-to-liquids by FT as commercially available. In the same 2021 report it left out the direct conversion of captured CO2 to syngas, and the use of electrolytic hydrogen, from the plant it evaluated, and it lists both as areas for future study.
Methanol synthesis is simpler on paper. Argonne gives the overall reaction as one CO2 molecule plus three hydrogen molecules giving methanol (CH3OH) plus water, run in two steps: reverse water-gas shift, then hydrogenation of the CO. Burning methanol later releases one CO2 molecule per methanol molecule, the same count taken in during synthesis. That is the "carbon loop" behind most e-fuel claims, and it is why the source of the CO2 matters so much.
A worked case: e-methanol and the effect of inputs
Argonne's study modeled methanol made from electrolytic hydrogen and high-purity CO2 from industrial plants. In its base case the hydrogen came from water electrolysis powered by wind or solar, and the methanol synthesis used U.S. average grid electricity. It compared three system designs against conventional methanol made from natural gas, which it puts at 91.5 g CO2e per MJ over the full life cycle, cradle to grave. CO2e means CO2-equivalent, a unit that adds different greenhouse gases together.
| System design | g CO2e per MJ | Reduction against 91.5 |
|---|---|---|
| Stand-alone methanol plant | 13.6 | About 85% (1 minus 13.6/91.5) |
| Attached to a corn ethanol plant | 37.9 | About 59% |
| Attached to an ammonia plant | 84.6 | About 8% |
Same fuel, same hydrogen, very different results. The gap comes from where the CO2 is taken and how emissions are shared. When the methanol unit is attached to an ethanol or ammonia plant, Argonne allocates the combined system's emissions among all products by their energy content, which shifts the methanol figure. The number depends on the accounting as much as on the chemistry. How such boundaries should be read is the subject of carbon-neutral fuel claims.
These are results from one modeling study, not a measurement of any plant. The figures describe methanol only and should not be placed beside gasoline or jet fuel life-cycle values, which use their own boundaries. The methanol itself is a different molecule: the AFDC lists a gallon of methanol at 0.50 gasoline gallon equivalents, and the Comparator's lower heating values (15.96 MJ/L against 32.36 MJ/L for gasoline) agree, at about half. More on that fuel is in methanol as a fuel.
Drop-in or not
Hydrocarbon products such as FT jet fuel are designed to match their petroleum counterparts. DOE says sustainable aviation fuel must meet the same fuel quality requirements as conventional jet fuel, which makes it compatible with existing airplanes and airport infrastructure. In practice the approval is by blend. FT synthetic fuel was added to the ASTM D7566 aviation standard in 2009 for blends of up to 50 percent with conventional jet fuel, according to AFDC, and NETL repeats that limit for FT jet fuel. DOE's fact sheet judges sustainable aviation fuels against a petroleum jet baseline of 89 g CO2e/MJ taken from the International Civil Aviation Organization's methodology. The basics of the fuel are in jet fuel explained.
To see the conventional fuels these products aim to replace, compare gasoline, jet fuel and methanol in the Comparator, which lists the conventional versions.
Common mistakes
- Reading "synthetic" as "chemically different." FT jet fuel is made to meet the same specification as petroleum jet fuel. The difference lies in the feedstock and the process.
- Using "e-fuel" for every synthetic fuel. An e-fuel needs hydrogen from electricity and captured CO2. Gas-to-liquids plants run on natural gas.
- Believing e-fuels burn without CO2. They release CO2 when burned. The climate claim rests on the CO2 captured during production.
- Assuming the name fixes the footprint. In Argonne's study the same e-methanol ranged from 13.6 to 84.6 g CO2e/MJ depending on the system design.
- Treating a certified blend as a fuel that can replace jet fuel entirely. FT synthetic jet fuel is approved in ASTM D7566 only for blends of up to 50 percent.
Frequently asked questions
What is the difference between a synthetic fuel and an e-fuel?
A synthetic fuel is any fuel built by chemical synthesis rather than refined from crude oil, whether the inputs are natural gas, biomass or CO2. An e-fuel is the subset made from electrolytic hydrogen and captured CO2, with low-carbon electricity as the energy source.
How is an e-fuel made, step by step?
Water is split into hydrogen by electrolysis, and CO2 is captured from an industrial plant or the air. The two are combined, in a route that goes through syngas, into a hydrocarbon fuel by Fischer-Tropsch synthesis or into methanol. Hydrocracking or similar upgrading then adjusts the product to the range needed.
Are e-fuels the same as biofuels?
No. Biofuels such as ethanol start from plant or animal material. E-fuels start from CO2 and hydrogen. The routes can overlap, since FT synthesis can also use gasified woody biomass as in AFDC's list of aviation fuel pathways, but the starting materials define the two groups.
Can synthetic jet fuel be used on its own?
Certification limits FT synthetic jet fuel to blends of up to 50 percent with conventional jet fuel under ASTM D7566, according to AFDC and NETL. NETL notes the fuel can run neat in an engine but is certified only in blends. The limit is a rule on approval, not a statement about the chemistry.
Sources
- Jet Fuel Production at the Pittsburgh Airport: GTL via Fischer-Tropsch Synthesis (DOE/NETL-2021/2853): National Energy Technology Laboratory. Accessed November 13, 2026.
- Techno-Economic and Life Cycle Analysis of Synthetic Methanol Production from Hydrogen and Industry By-product CO2 (Zang et al., Environmental Science and Technology, 2021): Argonne National Laboratory via OSTI. Accessed November 13, 2026.
- Sustainable Aviation Fuel: U.S. DOE Alternative Fuels Data Center. Accessed November 13, 2026.
- Sustainable Aviation Fuel: Reducing Emissions from Commercial Flight (DOE/EE-2365): U.S. DOE, Bioenergy Technologies Office. Accessed November 13, 2026.
- Fuel Properties Comparison: U.S. DOE Alternative Fuels Data Center. Accessed November 13, 2026.
Spotted something wrong or out of date? Tell us through the corrections page. We answer within 10 business days.