Fossil fuels

How Crude Oil Is Refined Into Fuels

A stunning aerial shot of an illuminated oil refinery at night showcasing industrial production in Rosemount, MN
Photo by Tom Fisk on Pexels. A general illustration, not evidence for any number.

A refinery turns crude oil into fuels in three kinds of steps. It separates the oil by boiling temperature, converts heavy parts into lighter ones, and then treats and blends the streams until each product meets its specification. Gasoline, diesel and jet fuel are different slices of the same crude oil, not separate raw materials.

No single unit "makes gasoline." The U.S. Energy Information Administration (EIA) reports that U.S. refineries made about 45 gallons of products from each 42-gallon barrel of crude oil in 2023, and the yield of each product varies from month to month. This guide follows the route from the crude oil tank to the product list, then shows the yield table.

Crude oil is a mixture, and the mixture sets the job

Crude oil is not one substance. A Sandia National Laboratories paper says crude oils are primarily hydrocarbons of the alkane and aromatic classes, and that they range from "light" oils of low density and viscosity to "heavy" ones similar to tar, and from low-sulfur ("sweet") to high-sulfur ("sour").

EIA classifies crude oil by density, measured as API gravity, and by sulfur content. Lighter crudes have more light hydrocarbons, and refineries can make high-value products from them with simple distillation. Heavy crudes need additional, more expensive processing, and high sulfur is undesirable for both processing and product quality. That is why the type of crude oil changes how much processing a refinery needs. How those oils formed is covered in how fossil fuels form.

Step one: separating by boiling point

Crude oil is heated in furnaces, and the resulting liquids and vapors enter distillation units. EIA says all refineries have atmospheric distillation units, and more complex ones also have vacuum units. The components separate into fractions by boiling point. The heaviest material settles toward the bottom of the column, and the lightest rises to the top.

  • Top: the lightest fractions, including gasoline and liquefied refinery gases.
  • Middle: medium-weight liquids, including kerosene and the distillates.
  • Lower: heavier gas oils.
  • Bottom: the heaviest fractions, with the highest boiling points.

Jet fuel and diesel come from the middle of this ladder. EIA's glossary defines kerosene-type jet fuel as a kerosene-based product meeting ASTM specification D 1655, with a distillation temperature of no more than 400°F (204°C) at the 10-percent recovery point and a final boiling point of no more than 572°F (300°C). Propane belongs to the gases at the light end. EIA says hydrocarbon gas liquids, a group that includes propane, are extracted both from natural gas at processing plants and from crude oil when it is refined. More on jet fuel is in jet fuel explained.

Distillation alone gives what the Sandia paper calls "straight-run" products. Early refineries made mostly these, but the paper says significant further processing of the fractions is typically necessary today to meet fuel specifications.

Step two: converting, cleaning and blending

Three kinds of work follow distillation.

Conversion. Cracking is the most widely used conversion method, according to EIA. It uses heat, pressure, catalysts and sometimes hydrogen to break heavy molecules into lighter ones, in fluid catalytic cracking units and hydrocrackers. Reforming turns naphtha, a light fraction, into high-octane gasoline components. Alkylation does the opposite of cracking: it combines gaseous byproducts of cracking into more gasoline components. The Sandia paper says reforming and alkylation raise the octane number by producing aromatics and branched alkanes, respectively. What octane measures is explained in octane rating explained.

Cleaning. The Sandia paper describes upgrading processes that remove impurities such as sulfur, nitrogen and metals. The most common technique is hydrotreating, a reaction with hydrogen over a catalyst at elevated temperature and pressure. EIA says on-highway diesel sold in the United States is ultra-low sulfur diesel, with 15 parts per million of sulfur or less. The reason is covered in ultra-low sulfur diesel explained.

Blending. For gasoline, technicians combine streams from the processing units, and octane level and vapor pressure determine the blend, EIA says. Refineries make unfinished gasoline called blendstocks, and at blending terminals these are mixed with fuel ethanol. EIA notes that most finished motor gasoline sold in the United States contains about 10% fuel ethanol by volume. The ingredients are covered in what gasoline is made of.

What one barrel yields

EIA's page on refinery inputs and outputs gives the average U.S. yield per 42-gallon barrel of crude oil input. As of November 2026, the page shows 2023 data and was last updated in June 2024.

Average U.S. refinery output per 42-gallon barrel of crude oil input, 2023 (EIA).
ProductGallons per barrelShare of total output
Finished motor gasoline19.5743.8%
Distillate fuel oil (mostly diesel)12.4727.9%
Kerosene-type jet fuel4.419.9%
Petroleum coke2.064.6%
Still gas1.683.8%
Hydrocarbon gas liquids1.553.5%
Asphalt and road oil0.841.9%
Residual fuel oil0.711.6%
All products, including some not listed44.65100%

The total exceeds 42 gallons. EIA explains that most products are less dense than the crude oil they come from, so their volume is larger, and it calls the increase processing gain. The arithmetic: 44.65 − 42 = 2.65 gallons, and 2.65 ÷ 42 = 6.3 percent, matching the page's figure of about 6.3 percent for 2023. The shares in the table are each product's gallons divided by 44.65.

The three main liquids end up close in energy per kilogram. On a lower heating value (LHV) basis, the Comparator lists gasoline at 43.45 MJ/kg (18,680 Btu/lb), diesel at 43 MJ/kg (18,487 Btu/lb) and jet fuel at 44.1 MJ/kg (18,960 Btu/lb), taken from different sources, and propane at 46.22 MJ/kg (19,873 Btu/lb). To see them side by side, compare gasoline, diesel, jet fuel and propane.

Common mistakes

  • Believing distillation alone makes finished fuel. Straight-run fractions usually need further processing to meet today's specifications, according to the Sandia paper.
  • Expecting 42 gallons of fuel from a 42-gallon barrel. Total output was 44.65 gallons in 2023, but part of that is petroleum coke, still gas, asphalt and other products that are not motor fuels.
  • Thinking each fuel comes from its own kind of crude oil. The fuels are different fractions of the same mixture. The crude type changes how much processing is needed, not which fuels are possible.
  • Treating diesel and jet fuel as the same product. EIA defines jet fuel by an ASTM specification and distillation limits, while diesel belongs to the broader distillate group.
  • Assuming propane comes only from gas wells. EIA says hydrocarbon gas liquids are extracted from natural gas at processing plants and from crude oil during refining.
  • Treating the yield table as fixed. EIA says refinery yields of individual products vary from month to month as refiners respond to demand.

Frequently asked questions

How much gasoline does a barrel of crude oil make?

EIA's yield table shows 19.57 gallons of finished motor gasoline per 42-gallon barrel of crude oil in 2023. Its FAQ gives a range of about 19 to 20 gallons of gasoline and 11 to 13 gallons of ultra-low sulfur distillate, most of it sold as diesel. Individual refineries and months differ.

Why does a 42-gallon barrel yield more than 42 gallons of products?

Most refined products are less dense than crude oil, so the same mass takes up more volume. EIA calls the increase processing gain and reports about 6.3 percent for U.S. refineries in 2023: 44.65 gallons of products from 42 gallons of crude oil.

What is cracking in a refinery?

Cracking breaks heavy hydrocarbon molecules into lighter ones using heat, pressure, catalysts and sometimes hydrogen. EIA names fluid catalytic cracking and hydrocracking as the main types. The Sandia paper says it lowers the molecular weight of the heavier fractions to values suited to the various fuel classes.

Is jet fuel made from the same crude oil as gasoline and diesel?

Yes. Jet fuel is a kerosene-based fraction of the same crude oil. EIA's definition requires it to meet ASTM specification D 1655, with distillation limits that place it in the middle of the boiling range, between the gasoline fraction at the top and the heavier gas oils below.

Sources

Spotted something wrong or out of date? Tell us through the corrections page. We answer within 10 business days.