Fuels in everyday life and history

How Power Plants Turn Fuel Into Electricity

A nuclear power plant's cooling towers emit steam at sunset, highlighting industrial infrastructure
Photo by Kyle Miller on Pexels. A general illustration, not evidence for any number.

A power plant burns fuel to make heat, uses the heat to spin a turbine, and lets the turbine spin a generator that produces electricity. In a steam plant the heat first boils water, and the steam turns the blades. In a gas turbine plant the hot gas from burning fuel turns the blades directly.

The electricity at an outlet is what the U.S. Energy Information Administration (EIA) calls a secondary energy source, made by converting primary sources such as coal and natural gas. As of November 2026, EIA's preliminary figures for 2025 show that about 41% of U.S. electricity generation came from natural gas and about 17% from coal. What is easy to miss is how much of the fuel's energy never becomes electricity. EIA's heat-rate numbers show it with one division.

The chain from fuel to outlet

Every plant in this article moves energy through the same four forms. Fuel holds chemical energy. Burning it releases heat. A turbine, a wheel of blades on a shaft, turns that heat into motion when a hot fluid pushes on the blades. A generator, connected to the same shaft, converts the motion into electricity. EIA describes the last two steps in nearly these words: the force of the fluid on the blades spins the rotor shaft, and the generator converts the rotor's mechanical energy to electrical energy.

What differs between plant types is the fluid that pushes the blades. In a steam plant it is steam. In a gas turbine it is the hot combustion gas itself. A combined-cycle plant uses both in sequence. The table below sets out the three types, with the share of U.S. generation that EIA reports for 2022.

Three kinds of turbine plant, what spins the turbine, and their share of U.S. electricity generation in 2022 (EIA).
Plant typeTypical fuelsWhat spins the turbineShare of 2022 U.S. generation
Steam turbine plantCoal, nuclear fuel, biomassSteam from a boiler or reactorAbout 42%
Combined-cycle plantNatural gas (99% of its energy)Hot gas, then steam made from the exhaust heatAbout 34%
Single-cycle gas turbineGaseous or liquid fuels, mainly natural gasHot combustion gas3.6%

Steam plants: boil water, spin the turbine

The Department of Energy's National Energy Technology Laboratory describes the sequence for a coal plant. Fuel burns in a large furnace, and the heat goes into a boiler that turns water into steam. The steam drives the turbine, which converts heat energy into kinetic energy. An axle connects the turbine to a generator that spins with it. Steam leaving the turbine is cooled and condensed in a heat exchanger, and the water is pumped back to be used again.

That last step explains why steam is not the fuel. It is a working fluid that circulates in a loop, while the fuel is whatever heats the boiler. Coal is the fuel in the plants described here, and the Comparator lists bituminous coal at 28.99 MJ/kg (12,465 Btu/lb) on a higher heating value basis. How coal types differ is covered in coal ranks and energy content. Nuclear plants also use steam, with a reactor in place of the furnace, and EIA says steam turbines accounted for about 42% of U.S. electricity generation in 2022.

Gas turbines and combined-cycle plants

A gas turbine skips the boiler. The U.S. Department of Energy (DOE) explains that a compressor draws in air and pressurizes it, fuel is injected into the air stream, and the mixture burns at more than 2,000 °F (about 1,100 °C). The hot gas expands through the turbine, spins its blades, and turns a generator. Most plants of this type burn natural gas, which EIA puts at 1,036 Btu per cubic foot (about 0.0386 MJ/L) as the U.S. average for gas delivered to consumers. EIA typically reports fuel energy as gross heat content, which is the higher heating value basis. The Comparator lists a different figure, 1,089 Btu per cubic foot (0.04057 MJ/L, higher heating value), because it uses gas at 32 °F and 1 atmosphere rather than EIA's reporting conditions.

The gas leaving the turbine is still very hot. A combined-cycle plant captures that exhaust heat in a heat recovery steam generator, makes steam, and runs a second, steam-driven turbine for extra electricity. EIA says combined-cycle plants supplied about 34% of U.S. net generation in 2022, and that natural gas made up 99% of the energy they used. DOE gives 20 to 35 percent as the energy conversion efficiency of simple-cycle gas turbines and says advanced turbines in its program reach as high as 60 percent.

How much of the fuel's energy becomes electricity

EIA reports a plant's heat rate, which is the fuel energy in Btu used to produce one kilowatt-hour (kWh) of electricity. A lower heat rate means less fuel per kWh. One kWh is 3,412 Btu, so dividing 3,412 by the heat rate gives the share of the fuel's energy that became electricity. Because EIA typically counts fuel energy as gross heat content, these shares are measured against the higher heating value.

Average operating heat rate of U.S. power plants in 2025 (EIA) and the efficiency it implies.
FuelHeat rate, Btu per kWh3,412 ÷ heat rate
Coal10,647About 32%
Petroleum10,969About 31%
Natural gas7,781About 44%

The arithmetic for coal is 3,412 ÷ 10,647 = 0.32, and for natural gas 3,412 ÷ 7,781 = 0.44. The remaining 68% (coal) and 56% (natural gas) mostly leaves as exhaust heat and as heat removed by cooling. That heat is not necessarily wasted: DOE says that when a gas turbine plant puts its waste heat to use for heating or industrial purposes, the overall energy cycle efficiency could approach 80 percent. EIA's averages cover utility and independent power producer plants and leave out combined heat and power plants.

A second view uses fuel quantities. EIA's 2022 averages were 1.14 pounds (0.52 kg) of coal, or 0.88 kWh per pound, and 7.42 cubic feet (0.21 m³) of natural gas for each kWh. Check the gas figure: 7.42 × 1,036 Btu = about 7,690 Btu, close to EIA's reported 2022 average of 7,740 Btu per kWh. The U.S. gas average of about 44% is a fleet-wide figure across many plant designs. DOE's efficiency ranges for gas turbines come from a different source and do not state a heating-value basis, so they should not be set directly against it. For the emissions side of this chain, see carbon intensity of electricity, and for the general idea of efficiency, energy efficiency and fuel efficiency. To put the fuels side by side, compare coal, natural gas and grid electricity.

Common mistakes

  • "Burning the fuel makes the electricity directly." In these plants burning makes heat. The turbine turns heat into motion, and the generator turns motion into electricity.
  • "Steam is the fuel." Steam is the working fluid. It is condensed and pumped back to the boiler, while the fuel is what heats it.
  • "A gas plant is a coal plant with a different fuel." A gas turbine uses hot combustion gas directly and has no boiler. Only a combined-cycle plant adds a steam stage, and it uses the exhaust heat to make the steam.
  • "All natural gas plants are equally efficient." DOE puts simple-cycle gas turbines at 20 to 35 percent and advanced turbines as high as 60 percent.

Frequently asked questions

How does a coal power plant make electricity?

Coal burns in a furnace, and the heat turns water in a boiler into steam. The steam spins a turbine, and an axle links the turbine to a generator that makes the electricity. The steam is then condensed back into water, cooled in a heat exchanger and pumped back to the boiler.

What is a combined-cycle power plant?

It is a plant that pairs a gas turbine with a steam turbine. The gas turbine burns fuel and spins one generator. Its hot exhaust then makes steam in a heat recovery steam generator, and that steam spins a second turbine for extra electricity. EIA says combined-cycle plants supplied about 34% of U.S. net generation in 2022.

How much coal or natural gas does it take to make one kilowatt-hour?

According to EIA's 2022 averages, about 1.14 pounds (0.52 kg) of coal or 7.42 cubic feet (0.21 m³) of natural gas per kilowatt-hour. Individual plants vary a good deal, so these are national averages, not figures for any one plant. The heat rate in Btu per kWh is the more direct way to compare plants.

Why do power plants lose so much energy as heat?

A turbine can turn only part of the heat into motion. The rest leaves with the exhaust gas or is removed when the steam is condensed and cooled. By the heat-rate arithmetic, about 68% of the energy in coal and 56% in natural gas left as heat in 2025.

Sources

Spotted something wrong or out of date? Tell us through the corrections page. We answer within 10 business days.